1.5ME_Technical Catalogue
20Pages

1.5ME Aluminium gear motors Technical Catalogue

GEAR MOTORS “E” - “B” - “C” SERIES Aluminium Body General Features GEAR MOTORS •Displacements from 2.8 cm3/rev to 73.4 cm3/rev (from 0.17 cu.in./rev to 4.48 cu.in./rev). •Rated pressure up to 250 bar (3625psi). •Back pressure capability up tp 120 bar (1740 psi) only in bi-directional release. •Speed up to 4500 rpm. •Flanges, shafts and ports for ISO, DIN and SAE standards. •Available in uni and bi-directional version for all the sizes, displacements and configurations. •High volumetric efficiency thanks to an innovative design and an accurate control of machining tolerances. •Axial...

GEAR MOTORS “E” - “B” - “C” SERIES Aluminium Body General Features DRIVE SHAFTS Radial and axial loads on the shafts must be avoided since they reduce the life of the unit. In order to avoid misalignment during the assembly with the primary engine, a connection with “Oldham” coupling (or coupling having convex toothed hub) is recommended. Anti - clockwise rotation MOTOR Clockwise rotation MOTOR Reversible rotation MOTOR HYDRAULIC PIPE LINE To calculate hydraulic pipe line size, the designer can use; as an approximate guide, the following fluid speed figures: From 6 to 10 m/sec on pressure...

Output lurque. Output fiOfiCi. V = Disp'aiement cm Yrev (m Vreu | P„ - IrMol pressu-* bar fpsij IP = P^ - P (syslem pressure) bar |psi | r. = Overall ef'ii eicy (q, ■ r)_) Output power: P = y ' n = °,,,P*r>i rh , Salami part number — Product short description FLUID POWER Product code (for Salami management) - Rotation sense Month and year of made

GEAR MOTORS “E” - “B” - “C” SERIES Aluminium Body General Features WORKING CONDITIONS Displacement *Available for quantity GROUP 2.5 - B SERIES The values shown in the picture represents the standard working situation. Max drain pressure is influenced by rotational speed of the unit. For pressure higher than 3 bar please contact sales department. On request available shaft seal for high P drain (20 bar).

GEAR MOTORS “E” SERIES Aluminium Body Final revised edition-April 2016 The data in this catalogue refers to the standard product. The policy of Salami S.p.A. consists of a continuous improvement of its products. It reserves the right to change the specifications of the different products whenever necessary and without giving prior information. If any doubts, please get in touch with our sales department.

GEAR MOTORS “E” SERIES Aluminium Body shafts and flanges combination 1.5ME CODE P0 - (Ø25,4 mm) European standard CODE P01 - (Ø30 mm) European standard CODE S0 - SAE AA 2 bolts CODE S1 - SAE AA 4 bolts

GEAR MOTORS “E” SERIES Aluminium Body Displacements up to 0.67 cu.in./rev Pressure up to 3625 psi GEAR MOTORS Pdrain < 3 bar (43 psi) ASSEMBLING DIMENSIONS For flanges code: P0-P01-S0, this dimension is 18 mm (0.71 in.) S1, this dimension is 40 mm (1.57 in.) Only for Reversible rotation

GEAR MOTORS “E” SERIES Aluminium Body FLANGED and THREADED PORTS UNI-DIRECTIONAL MOTORS BI-DIRECTIONAL MOTORS *Only for Reversible rotation code P Flanged ports european standard UNI-DIRECTIONAL MOTORS BI-DIRECTIONAL MOTORS *Only for Reversible rotation code B Flanged ports german standard TYPE UNI-DIRECTIONAL MOTORS Threaded ports GAS (BSPP) BI-DIRECTIONAL MOTORS UNI-DIRECTIONAL MOTORS

GEAR MOTORS “E” SERIES Aluminium Body DRIVE SHAFTS

GEAR MOTORS “E” SERIES Aluminium Body MOUNTING FLANGES European standard European standard With shaft code 18 With shaft code 19 SAE AA 2 bolts With shaft code 51-80 SAE AA 4 bolts With shaft code 83

GEAR MOTORS “E” SERIES Aluminium Body REAR COVERS WITH RELIEF VALVE code VS With main relief valve with internal unloading line. Rear cover with fixed setting main relief valve. Available values of fixed setting (20bar-250bar/290psi-3625psi) (Standard setting are multiple of 10 bar).

GEAR MOTORS “E” SERIES Aluminium Body PERFORMANCE CURVES Performance curves carried out with oil viscosity at 21 cSt and oil temperature at 50°C Output torque / Power 14.00 Flow [l/min] Flow [l/min] Output torque / Power 1.5ME - 3.5 Output torque / Power 16.00 Flow [l/min]

GEAR MOTORS “E” SERIES Aluminium Body Output torque / Power 8.00 Flow [l/min] Output torque / Power Flow [l/min] Flow [l/min] Output torque / Power

GEAR MOTORS “E” SERIES Aluminium Body Output torque / Power 35.00 Flow [l/min] Output torque / Power Flow [l/min]

GEAR MOTORS “E” SERIES Aluminium Body VALVES IN THE COVER (page 136) Adjustable main relief valve Buna standard MOUNTING FLANGES (page 135) European standard European standard Flanged ports european standard Flanged ports german standard Threaded ports GAS (BSPP) DRIVE SHAFTS (page 134) Order example 1.5ME 11.3D, ports SAE (R), drive shaft (82), mounting flange (S2). 1.5ME11.3D-R82S2

You can find our most up to date “STANDARD SALES CONDITIONS” on our website. Potete trovare le nostre più aggiornate “CONDIZIONI DI VENDITA STANDARD” sul nostro sito. Watch our tutorials on youtube channel Salami Fluid Power Salami Fluid Power World Salami Fluid Power France Salami Fluid Power España Salami Fluid Power

SALAMI S.P.A. Via Emilia Ovest 1006 41121 Modena (Italy) T. +39 059 387 411 F. +39 059 387 639 sales@salami.it SALAMI FRANCE 22, rue Louis Saillant 69120 Valux en Velin Lyon T. +33-04-78809941 F. +33-04-78804264 e.pasian@salami.fr SALAMI ESPAÑA Poligono Industrial Armenteres C/Primer de Maig, 18, Nave 4 08980 San Feliu de Llobregat Barcelona T. +34-93-6327288 F. +34-93-6667826 info@salamispain.com SALAMI HYDRAULICS N.A INC Loop Road Baldwinsville NY 13027 - USA T. +1-315-295-2363 F. +1-315-295-2364 info@salamihydraulics.com