Oil and Gas
24Pages

. , , r , , , . , . driven by technology Clamping technology for crude oil and natural gas industries

CRUDE OIL AND NATURAL GAS THE ENERGY OF TODAY RÖHM is the specialist for clamping technology with a wide product range, unrivaled with regard to variety. This solutions for special requirements are also unlimited in the oil and gas extraction areas. The crude oil and natural gas industries are still the center of the worldwide energy production today. The extraction and further processing of these two raw materials require top precision and maximum safety. RÖHM products are characterized by just these properties. In the past years, RÖHM was able to increasingly adapt the product range to...

CONTENT Machining of Pipes Overview Pneumatic Front-End Chucks Operation Guide Pneumatic Front-End Chucks Pneumatic Front-End Chucks LVE LVE-ES LVE-AZ ES LVE-FAZ EC LVE-VZA Centering Chucks KFG Overview Hydraulic Front-End Chucks Operation Guide Hydraulic Front-End Chucks Machining of Bushings Swivel Chucks Special Solutions Stationary Centering and Clamping Unit Center Drive Chuck Machining of Drill Bits Special Solutions

PIPE MACHINING: PNEUMATIC FRONT-END CHUCKS The pneumatic front-end chucks are optimally suited for machining the ends of pipes, especially large and long pipes like the ones used for extracting crude oil or natural gas. For this, a chuck is mounted to the front and rear sides of the machine spindle. This combination allows large chipcutting performance at high turning precision. Setup and mode of operation A special feature of this chuck is a pneumatic piston built into the chuck body and supplies the chucking power. The workpiece is clamped or released by compressed air supplied, with...

PIPE MACHINING: PNEUMATIC FRONT-END CHUCKS Components LVE 1. Body 2. Base jaw 3. Piston 4. Protective bush 5. Intermediate washer 6. Piston plate 7. Flange 8. Distributor ring 9. Seal 10. T-Nut 11 . Air-vent screw 12. Control valve 13. Jaw fixing screws 14. Chuck fixing screws PNEUMATIC CONTROL UNIT CONTROL UNIT FOR DUAL CHUCKS Control voltage 24 V Connection R 1/2" inside thread Weight approx. 3 kg Dimensions: 280x250x100 mm (WxHxD) Item no.: 426560 With dual foot switch, wired, 6m cable Control voltage 24 V Dimensions: 300x300x120 mm (WxHxD) Width with plug: 340 mm Item no.: 426482...

OPERATION GUIDE LVE TYPE - Pneumatic front-end chuck - Concentric clamping - Pneumatic front-end chuck - Concentric clamping - With rapid stroke and clamping stroke Machining situation: Bent pipe Centering via centering chuck ng Machining situation: Bent pipe Centering by front-end chuck g y Machining situation: Exactly straight pipe No centering required ring rapid stroke and clamping stroke with compensation retractable clamping arms for pre-centering low-maintenance (Easy Care)

LVE-AZ ES - Pneumatic front-end chuck - Concentric clamping or with compensation - With rapid stroke and clamping stroke 10 LVE-FAZ EC - Front-end chuck - Clamping with springs, pneumatic release - Concentric clamping or with compensation - Low-maintenance design LVE-VZA - Pneumatic/spring-operated front-end chuck - Concentric clamping or with compensation - Retractable clamping arms for pre-centering the workpiece Centering chuck KFG - Pneumatic angle lever chuck - Concentric clamping - Integrated flapper with stroke inquiry ideally suited rear-end chuck fr front-end chuck with centering w...

C 15 3-jaw self-contained chucks LVE, with large through-hole, max. operating pressure 8 bar, with serration, cylindrical center mount Standard design Id.-Nr.

large through-hole, with rapid and clamping jaw movements C 15 3-jaw self-contained chucks LVE, with rapid and clamping jaw movements, with large through-hole, external chucking, max. operating pressure 8 bar, with serration, cylindrical center mount

The hydraulic front-end chucks are optimally suited for machining the ends of pipes, especially large and long pipes like the ones used for extracting crude oil or natural gas. For this, one chuck is mounted to the front and one to the rear side of the machine spindle. This combination allows large chipcutting performance at high turning precision. Actuation HVE-IZ During pipe machining, the clamping system is decoupled from the supply via relief valves. A pressure accumulator ensures a sufficient resupply. A sensor system detects any drop in pressure. The HVE-IZ chuck is actuated...

PIPE MACHINING: HYDRAULIC FRONT-END CHUCKS HVE with injection cylinders Components HVE-IZ 6 Body Base jaw Clamping piston with floating clamping claw disc, concentric positionable Protection bush Piston Pressure accumulator Centering bar Centering piston Oil supply flange Retaining ring Injection cylinder Control injection cylinder Pressure control Additional control for spindle zero point Oil supply pipe for front-end chuck Relief valve 4 Different versions available on request The hydraulic chuck as well as the necessary accessories are available on request. We would be happy to advise...

OPERATION GUIDE HVE TYPE - Hydraulically operated front-end chuck - Actuation via injection cylinders - Concentric clamping or with compensation - With rapid stroke and clamping stroke HVE-IZ V AZ ES - Hydraulically operated front-end chuck - Actuation via injection cylinders - Concentric clamping or with compensation - With rapid stroke and clamping stroke - Retractable clamping arms for pre-centering the workpiece Machining situation: Bent pipe Centering via centering chuck Machining situation: Bent pipe C i b f d h k Centering by front-end chuck rapid stroke and clamping stroke with...

- Hydraulically operated front-end chuck - Stationary actuation - Concentric clamping or with compensation - With rapid stroke and clamping stroke - Hydraulically operated front-end chuck - Stationary actuation - Concentric clamping or with compensation - With rapid stroke and clamping stroke - Retractable clamping arms for precentering the workpiece Centering chuck From a wide range of centering options, we will select the right centering chuck for your machining application ideally suited bent pipe rear-end chuck front-end chuck with centering exactly straight pipe front-end chuck...