Laser Scanners RF620HS(DHS) - RIFTEK - #9

SV\CHR.ONlZAT.ON

I he scanner can work ivith 5 independent synchronization m|.ul'. All types of syncliroili/alinn on respond lo itipul status, if external .>i.clironi-alion is allowed. Ihe ik of external synch ionization

enabled wiili the i-nii-'|iuri[liiii.' hni, described below. S\ni-lir«nii!ati»norr«9«li:

The funetion is possible onlv if the sensor is equipped with the result sync hronizn lion input iscehittll □d«fo[uj").

bitO: if 0 (by default), t DP packages arc transmuted wiih no external synchronization taken into account according (o "host II' address" and ■host port" parameter, at fre­quency "UDP rn.-inicni.-i" specified in ihe "V-lMork settings" field, if I. external synchronization is enabled. If an event (bitJl occurs al TTL INPUTO inpul. 1 111' |i;nk;i!'t is transmitted according in "liosl II' address" and "hn.l poit" p.i ramCtCTs specified in the "Sclwork settings" I'n-kl.

bill: if 0 (by default). synchronization of die result based on ihe leading edge of the pulse takes place;

ifl. synchronization of the result based on the nailing edge takes plaee; This makes sense if bilO is set to I. Ninrlirmii/atimi iif iiu-nMiri-inenl:

The function is possible only if die sensor is equipped wnli the measurement synchroniza­tion input (see bit02 uclnfolOl).

bil2: if Olby default!, readout occurs with nocllcnul synchroniatkm taken iniu acciiuil •tinnvmiiiiii possible internal frequency. ¡1' 1. external ..ivho.iiiz.iUnn i- enabled.

[ran event (bit! I occurs at TTL INPUT I input, measurement cycle l*i nl eg ration" ■■rcad»iU"-"ealcnl:iliou" cycle) lakes plaee al a g»eti exposure willl [lie "Divisor" and "Delay" paiaiuclcr- laken into aeeount in llie "I Mental .yiichionizalion" field; bit?: if 0 (by delimit I. synchronization of nicastircniem based on the leading edge of the

The function i- |io.sihlc ottk it' die sensor is equipped with analog outputs (sec biM3 uclift-iO]).

bh4: if 0 (by default!, coordinates are sent at a maximum possible rrequency to analog outputs according to ihe "Ntimhei of points" ami -Point holdup" parameters speci­fied in ihe 'Analog oulpuls" Held.

if I, external synchronization is enabled: If an event (bit?) occurs at TT1. INPUT:

llipn:. c.....da laics .„.■ .,nl lo analog outputs .ici old lag io III.- -\lillllvi ol points' an.I

"Point holdup" parameters specified hi the "Analog outputs" field: bit5- if 0 (by default), synchronization of analog oulpuls on the leading edge of the pulse lakes plaee;

if I. synchronization of analog outputs on ilic nailing edge takes place; bit6: level of TTI. Of It) signal of valid data al the analog output. By default 0.

Divisor - specifics parameter oI external signal dni.iou from ii to 255. which corresponds lo Mm By default 0.

Pauc 9/22 Rev. A (14.I)4.20<W)-

km Ilk Republic of flelarus. \.....k.id to: i.t7J.t1-:s|.JSI.i i;-™.....n№<rria_l;k.«>m.li<i|«v^j.lMi,cMI