LPAX/MPAX - Red Lion Controls - #4

Text version of the page

Once assembled, the LPAX and MPAX have all the same functions and capabilities of our PAX Series Intelligent Panel Meters. Therefore, you will find the appropriate PAX information packed with the MPAX Module. Simply follow the instructions to wire and program the display for your application. TROUBLESHOOTING For technical assistance, contact technical support. 2.0 INSTALLING THE DISPLAY 3.0 WIRING AND PROGRAMMING THE DISPLAY LPAX DISPLAY INSTALLATION The LPAX display is intended to be mounted into a panel or enclosure. The display is provided with a gasket to provide a water-tight seal. The recommended minimum panel thickness for NEMA 4/IP65 sealing is 0.060" (1.57 mm). For panel mounting, prepare the panel cut-out to the dimensions shown. The supplied template may be used to mark the cut-out and hole locations on the panel. After the panel cut-out has been deburred, slide the panel gasket over the rear of the display and onto the mounting studs. Insert the display into the panel cut-out as illustrated in Figure 3. Install six # 10-32 keps nuts (supplied) and tighten evenly for uniform gasket compression. Do not over-tighten the nuts. By using additional mounting accessories, the LPAX can be surface-wall mounted, suspended, or bottom mounted. Separate installation instructions are provided with the mounting accessories. Environment And Cleaning The display should be installed in a location that does not exceed the maximum operating temperature and provides good air circulation. Placing the system near devices that generate excessive heat should be avoided. The bezel should be cleaned only with a soft cloth and neutral soap product. Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the aging process of the bezel. Figure 3, Installing The LPAX Into A Panel SFCRD** Crimson 2 PC Configuration Software for Windows 98, ME, 2000 and XP SFCRD200 Accessories LX* Custom Units Label Listed Separately PAXCDC50 PAXCDC4C PAXCDC40 PAXCDC30 Profibus-DP Communications Card Extended Modbus Communications Card with Dual RJ11 Connector Modbus Communications Card DeviceNet Communications Card Optional Plug-In Cards MBLPAX00 SHRLPAX0 PAXCDL Analog Output Card PAXCDL10 Mounting Bracket for LPAX Shroud for LPAX PAXCDC2C PAXCDC20 Extended RS232 Serial Communications Output Card with 9 Pin D Connector RS232 Serial Communications Output Card with Terminal Block MB SHR PAXCDC1C PAXCDC10 Extended RS485 Serial Communications Output Card with Dual RJ11 Connector RS485 Serial Communications Output Card with Terminal Block PAXCDC ENC90000 Quad Setpoint Sourcing Open Collector Output Card PAXCDS40 ENC9 NEMA 4 Enclosure for LPAX Quad Setpoint Sinking Open Collector Output Card PAXCDS30 Analog Input Module Display Quad Setpoint Relay Output Card PAXCDS20 TYPE MPAXT010 MPAXS010 MPAXP010 MPAXD010 Dual Setpoint Relay Output Card PAXCDS10 PAXCDS Thermocouple and RTD Module, DC/24 VAC Powered Strain Gage Input Module, DC/24 VAC Powered Process Input Module, DC/24 VAC Powered Universal DC Input Module, DC/24 VAC Powered MPAXT000 MPAXS000 MPAXP000 MPAXH000 MPAXD000 LPAX0500 Thermocouple and RTD Module, AC Powered Strain Gage Input Module, AC Powered Process Input Module, AC Powered AC True RMS Voltage and Current Module, AC Powered Universal DC Input Module, AC Powered 5-Digit, Large Display for Analog MPAX Modules MPAX LPAX MODEL NO. DESCRIPTION PART NUMBERS ORDERING INFORMATION * See the LPAX Accessory Bulletin or our web site for available units labels. ** Crimson software is available for download from http://www.redlion.net/