Catalog AS-interface - PEPPERL & FUCHS

Catalogue Catalog AS-interface

www.pepperl-fuchs.com

Page

/ 356

PEPPERL & FUCHS - 306470, 100016, 94043, 100068, 17451, 94481, 100749, 89521

/ 356

See other catalogues for PEPPERL & FUCHS

Text version of the page


	AS-Interface industrial gateway
	Technical data
	General specifications
	AS-Interface specification	V2.11
	Indicators/operating means
	LC display, two-digit	address display, error message
	LED BUS ACTIVE	PROFIBUS master detected; LED green
	LED AS-i ACTIVE	AS-Interface operation normal; LED green
	LED CONFIG ERR	configuration error; LED red
	LED PRG ENABLE	autom. programming; LED green
	LED ENERGY	voltage ON; LED green
	LED PRJ MODE	projecting mode active; LED yellow
	LED U AS-i	AS-Interface voltage; LED green
	Switch SET	Selection and setting of a slave address
	OK button	Mode selection traditional-graphical/confirmation
	Button MODE	Mode selection PRJ-operation/save configuration/cursor
	ESC button	Mode selection traditional-graphical/cancel
	Electrical specifications
	Insulation voltage U_i	> 500 V
	Rated operational voltage U_e	from AS-Interface
	Rated operational current I_e	< 180 mA from AS-Interface
	Interface
	Protocol	PROFIBUS
	Interface type	RS 485
	Transfer rate	9.6; 19.2; 44.44; 93.95; 187.5; 500; 1500 kBit/s self-synchronising
	Connection
	PROFIBUS	Sub-D interface
	AS-Interface	screw terminals
	Ambient conditions
	Ambient temperature	0 ... 55 °C (273 ... 328 K)
	Storage temperature	-15 ... 75 °C (258 ... 348 K)
	Mechanical specifications
	Protection degree	IP20 according to DIN 40050
	Mass	420 g
	Construction type	terminal rail housing, LDG-A-30

VBG-PB-K20-D

Function

■a

TO >'

0) <D

W TO

The VBG-PB-K20-D is a PROFIBUS Professional gateway in accordance with AS-Interface specification 2.11 in IP20. The design is especially suitable for use in the switch professional cabinet.

The VBG-PB-K20-D is a modular PROFIBUS slave. This means that the user can use the PROFIBUS configuration tool to specify what data will be transferred via the PROFIBUS. This makes it possible to adjust the amount of data to be transferred via PROFIBUS.

In addition, this gateway supports acyclical communication of the PROFIBUSDP V1. These acyclical services can be used to access a mailbox in the gateway that provides access to all the data made available by the AS-Interface/Profibus gateway. A push button can be used to accept the target configuration and to adjust the PROFIBUS address and baud rate. There are 7 LEDs on the front panel, showing the current status of the AS-i line. In the case of the AS-Interface Gateway with graphical display, the AS-Interface circuit can be placed in service and the test of the connected periphery can be kept entirely separate from the commissioning of the PROFIBUS and the programming. On-site operation with the aid of the graphical display and 4 push buttons makes it possible to show all functions on the display that are covered by the AS-i Control Tools professional software for other AS-Interface masters. An additional RS 232-socket offers the option of reading data via gateway, network and function as part of advanced local diagnostics directly from the gateway.

SUPPLIERS OF PLC functionality

Optionally the gateway is also available with PLC-functionality.

Accessories VAZ-SW-ACT32

Full version of the AS-i Control Tools VAZ-PB-SIM

PROFIBUS master professional simulator

«.Ì %JE -5 <° ^i? S 2

— o

V) ™

°> ro = <2

0;g

.Sì Litt

o E a>

3 O)

Software

The device is supplied with the configuration data files (GSD) as well as a restricted version of the AS-i Control Tools software. The software performs the addressing, programming and monitoring of the AS-Interface network. The full version of the AS-i Control Tool is available as an accessory and features an expanded diagnostics professional monitor as well as a larger program memory for AS-Interface Control which makes it possible to detect faulty telegrams of slaves. A GSD file can be easily created for the PROFIBUS DP using the GSD assistant, whereby the size of the I/O windows can be conveniently adapted to the AS-Interface circuit's load and the AS-Interface configuration can be stored within the GSD file. A text file is also created, which documents the status of AS-Interface data in the gateway's I/O window. Note:

The VAZ-PB-SIM accessory is required for the AS-i Control Tool.

~a o E

a> .c

a> (/> a> .>

% £ a> o ~äi v>

O (/)

Q-

o o

(/)

^ (/) (/) a> o o <

o o

CD CO

£ <

CD o

Subject to reasonable modifications due to technical advances.

• Internet http://www.pepperl-fuchs.com 31

Pepperl+Fuchs Group • Tel.: Germany +49 621 776-0 • USA +1 330 4253555 • Singapore +65 67799091