Group: INDUSTRIAL GROUP
Catalog excerpts
Rugged Single-Axis Hall-effect Joystick Contactless – Hall-effect technology Single axis control with spring to center or friction hold lever action Choice of grips including Center and End Locking 5Vdc or 9-30Vdc supply Dual channel output with optional ramp directions Analogue (Vdc) or Digital (PWM) outputs Extremely low signal noise – less than 1mV rms Operating temperature -40 to +85°C Environmental protection up to IP69K above the panel – dependent on grip selected Electronics sealed to IP69K 53mm under-panel depth The JC1500 joystick utilizes contactless rotary position sensor technology combined with a rugged, low profile design. The joystick provides reliable and accurate output signals - and includes a second output to enable error checking of the system integrity. The JC1500 is intended for use in the off-highway specialist vehicles market - particularly where reliability and strength are paramount e.g. Aerial Work Platforms. The JC1500 joystick complements the existing range of JC150 potentiometer track joysticks and has the same panel mounting details – allowing replacement or upgrade with no panel modifications. If a JC1500 is used to replace a JC150 joystick then due consideration needs to be taken of the supply voltage This JC1500 joystick is designed to share the same range of handles and grips as used in the JC150 and JC60
Open the catalog to page 1SPECIFICATIONS SUPPLY SUPPLY VOLTAGE SUPPLY CURRENT OVER VOLTAGE REVERSE POLARITY PROTECTED POWER-ON TIME 220 mm long 4 core (24 AWG) Flying lead ANALOGUE OUTPUT OUTPUT VOLTAGE (5V) OUTPUT NOISE INPUT/OUTPUT DELAY DIGITAL (PWM) OUTPUT PWM FREQUENCY 244Hz ± 20% over temperature range 10-90% over measurement range GENERAL OUTPUT DATA RESOLUTION LOAD RESISTANCE SHORT CIRCUIT PROTECTION Output to GND and output to supply in 5V mode MECHANICAL ANGLE 530g without handle fitted LEVER OPERATING FORCE (spring return to center) Maximum allowable (Spring return and friction) 110Nm on axis of movement...
Open the catalog to page 2All CURTISS-WRIGHT catalogs and technical brochures
-
S-Drive
2 Pages
-
AES-350
18 Pages
-
AES-349
25 Pages
-
Industrial Division
8 Pages
-
Transmission Shifter
2 Pages
-
SBW
3 Pages
-
newVSI Brochure
2 Pages
-
Multi-Function Grip
2 Pages
-
SCM100
3 Pages
-
wm-67
2 Pages
-
wm-672
2 Pages
-
wm-674
1 Pages
-
wm-68a
2 Pages
-
wm-762
2 Pages
-
wm-763
2 Pages
-
wm-764
2 Pages
-
WM-777
2 Pages
-
WM-782
3 Pages
-
WM-783
3 Pages
-
WM 784
2 Pages
-
wm-80
2 Pages
-
WCS-133284
5 Pages
-
WM 81
2 Pages
-
WCS-134143
5 Pages
-
Tilt Position Sensor
4 Pages
-
Industrial Group
4 Pages
-
Sealed Tilt Sensor STT280
2 Pages
-
Sealed Tilt Sensor STT500
2 Pages
-
Aerial Work Platforms
4 Pages
-
AES-204
13 Pages
-
ML1951
1 Pages
-
ML1441 AC
1 Pages
-
Diagnostic Test Tool
2 Pages
-
WM526
2 Pages
-
CW-IG-Overview Brochure
8 Pages
-
JC050
2 Pages
-
JC040
2 Pages
-
WM547 Rotary hand control
2 Pages
-
WM535 Lever hand control
2 Pages
-
C7 Hydraulic Lever
2 Pages
-
C6 Hydraulic Lever
2 Pages
-
RF15 Series
2 Pages
-
RF11 Series
2 Pages
-
PGFM3000 Series
3 Pages
-
PGF8000 Series
4 Pages
-
PGF7000
1 Pages
-
PGF3000 Series
4 Pages
-
CW-IG-Overview
8 Pages
-
CW-IG-On-Highway
4 Pages
-
CW-IG-Medical Mobility
4 Pages
-
CW-IG-Industrial
4 Pages
-
CW-IG-Construction
4 Pages
-
PGFX3000 Series
2 Pages
-
PGFM8000 SERIES
4 Pages
-
On-Highway
4 Pages
-
GK1037
1 Pages
-
GK0730
1 Pages
-
Permanent Magnet
1 Pages
-
GD1444
1 Pages
-
D-Frame Solenoid
1 Pages
-
CW-IG-Agriculture
4 Pages
-
SRH220DR
2 Pages
-
STT280
2 Pages
-
CW-IG-Material Handling
4 Pages
-
C3-CE AC Motor Controller
2 Pages
-
C3-36V - AC Motor Controller
2 Pages
-
WM531 Remote sensor control
2 Pages
-
WM526 Electronic floor pedal
2 Pages
-
WM537 Electronic floor pedal
2 Pages
-
WM558 Electronic floor pedal
2 Pages
-
SRS Sealed Rotary Sensors
8 Pages
-
STT series Sealed Tilt Sensors
12 Pages
-
Holding Magnets
2 Pages
-
Digital Panel Indicators
8 Pages
Archived catalogs
-
ICS100 IN-CYLINDER SENSORS
8 Pages