Group: INDUSTRIAL GROUP
Catalog excerpts
36V AC traction controller, particularly suitable for ride-on floorcare machines 200Arms motor output Compatible with all AC induction motors Versatile throttle & brake pedal inputs Three coil outputs Intelligent Hill-Hold function Programmable start-up sequence options Low battery management CANopen comms On-board Status LEDs Integrated service timers Sealed to IPx5 Designed to the requirements of EN60335-2-72 and UL583 Although primarily intended as an advanced, cost-effective, AC traction controller for floorcare machines, the 36V variant of PGDT’s C3 range is equally suitable for other small, rideon vehicles. Flexible, yet simple programming means the controller is compatible with all types of AC induction motor, while a dedicated thermistor input allows motor temperature and the power to the motor to be reduced if it is becoming too warm. The 36V C3 features up to eight dedicated digital inputs that can be individually switched to 0V, open-circuit, B+ or a combination of these options to provide the active state. The controller also accepts multiple throttle and brake pedal types, including 2- or 3-wire resistive and voltage. CANopen hardware is provided as standard, offering vehicle OEMs maximum input flexibility. Three, 2A outputs allow for control of a line contactor, electromagnetic brake and reversing alarm. All outputs are protected against wiring errors and contain coil suppression circuits, meaning external diodes are not required. To ensure maximum efficiency, the 36V C3 employs an intelligent Hill-Hold function that only takes power from the battery if the vehicle starts to roll. As soon as it is detected that Hill-Hold is not required, then no further power will be consumed. Traditionally, application of a brake switch has been needed to provide this function. In addition to on-board LEDs that can communicate basic status and diagnostic information, the controller includes two service timers – one for keyswitch hours and one for operational ‘active’ hours. These can be set by an OEM or service agent, thereby ensuring an appropriate maintenance regime. After a service is complete, the timers can be set to the next service interval. The innovative construction methods employed by the 36V C3 ensure reliable and repeatable assembly of the electronic enclosure, which results in consistent protection of the electronic circuits from the environment and efficient transfer of heat to the baseplate. The design is compliant with all relevant international floorcare vehicle standards, e.g. EN60335-2-72 and uses UL approved materials throughout, taking into account the critical dimensions defi
Open the catalog to page 1SPECIFICATIONS ELECTRICAL SUPPLY VOLTAGE PEAK VOLTAGE REVERSE BATTERY VOLTAGE COIL OUTPUTS TRACTION MOTOR OUTPUT – 2 MINS TRACTION MOTOR OUTPUT – 1 HR MECHANICAL POWER CONNECTIONS CONTROL CONNECTIONS ENVIRONMENTAL MOISTURE RESISTANCE OPERATING TEMPERATURE STORAGE TEMPERATURE PRODUCT CODES CONTROLLERS C3-200-CAN 36V DISPLAYS iGAUGE Diagnostic Test Tool, hand-held programmer PC Programmer, service access PC Programmer, OEM and manufacturing access © 2014 Curtiss-Wright. All rights reserved. Specifications are subject to change without notice. All trademarks are property of their respective...
Open the catalog to page 2All CURTISS-WRIGHT catalogs and technical brochures
-
S-Drive
2 Pages
-
AES-350
18 Pages
-
AES-349
25 Pages
-
Industrial Division
8 Pages
-
Transmission Shifter
2 Pages
-
SBW
3 Pages
-
newVSI Brochure
2 Pages
-
Multi-Function Grip
2 Pages
-
SCM100
3 Pages
-
wm-67
2 Pages
-
wm-672
2 Pages
-
wm-674
1 Pages
-
wm-68a
2 Pages
-
wm-762
2 Pages
-
wm-763
2 Pages
-
wm-764
2 Pages
-
WM-777
2 Pages
-
WM-782
3 Pages
-
WM-783
3 Pages
-
WM 784
2 Pages
-
wm-80
2 Pages
-
WCS-133284
5 Pages
-
WM 81
2 Pages
-
WCS-134143
5 Pages
-
Tilt Position Sensor
4 Pages
-
Industrial Group
4 Pages
-
Sealed Tilt Sensor STT280
2 Pages
-
Sealed Tilt Sensor STT500
2 Pages
-
Aerial Work Platforms
4 Pages
-
AES-204
13 Pages
-
ML1951
1 Pages
-
ML1441 AC
1 Pages
-
Diagnostic Test Tool
2 Pages
-
WM526
2 Pages
-
CW-IG-Overview Brochure
8 Pages
-
JC050
2 Pages
-
JC040
2 Pages
-
WM547 Rotary hand control
2 Pages
-
WM535 Lever hand control
2 Pages
-
C7 Hydraulic Lever
2 Pages
-
C6 Hydraulic Lever
2 Pages
-
RF15 Series
2 Pages
-
RF11 Series
2 Pages
-
PGFM3000 Series
3 Pages
-
PGF8000 Series
4 Pages
-
PGF7000
1 Pages
-
PGF3000 Series
4 Pages
-
CW-IG-Overview
8 Pages
-
CW-IG-On-Highway
4 Pages
-
CW-IG-Medical Mobility
4 Pages
-
CW-IG-Industrial
4 Pages
-
CW-IG-Construction
4 Pages
-
PGFX3000 Series
2 Pages
-
PGFM8000 SERIES
4 Pages
-
On-Highway
4 Pages
-
GK1037
1 Pages
-
GK0730
1 Pages
-
Permanent Magnet
1 Pages
-
GD1444
1 Pages
-
D-Frame Solenoid
1 Pages
-
CW-IG-Agriculture
4 Pages
-
SRH220DR
2 Pages
-
STT280
2 Pages
-
CW-IG-Material Handling
4 Pages
-
C3-CE AC Motor Controller
2 Pages
-
WM531 Remote sensor control
2 Pages
-
WM526 Electronic floor pedal
2 Pages
-
WM537 Electronic floor pedal
2 Pages
-
WM558 Electronic floor pedal
2 Pages
-
SRS Sealed Rotary Sensors
8 Pages
-
STT series Sealed Tilt Sensors
12 Pages
-
Holding Magnets
2 Pages
-
Digital Panel Indicators
8 Pages
Archived catalogs
-
ICS100 IN-CYLINDER SENSORS
8 Pages