Steam Traps - Pennant Engineering - #29

Text version of the page

Untitled table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:7.00pt "Arial", sans-serif; } .font1 { font:8.00pt "Arial", sans-serif; } .font2 { font:9.00pt "Arial", sans-serif; } .font3 { font:10.00pt "Arial", sans-serif; } .font4 { font:12.00pt "Arial", sans-serif; } .font5 { font:17.00pt "Arial", sans-serif; } .font6 { font:24.00pt "Arial", sans-serif; } PENN0NT PT22 Inverted Bucket Steam Traps - (Cast Iron) MATERIAL: No PART MATERIAL QTY. (Nos.) 1. BODY CAST IRON 01 2. COVER CAST IRON 01 3. BUCKET ASSLY. AISI 304 01 4. LEVER ASSLY. AISI 304 01 5. VALVE SEAT (HARDENED) 13% CR STEEL / AISI 410/420 01 6. BRACKET AISI 304 01 7. VALVE PIN (HARDENED) 13% CR STEEL / AISI 410/420 01 8. GASKET (COVER) CAF / Non CAF 01 9. BOLT ASTMA193 Gr. B7 06 10. PLUG CARBON STEEL 02 11. GASKET (PLUG) CAF / Non CAF 02 12. LOCATING TUBE STAINLESS STEEL 01 DIMENSIONS - Nominal in mm MODEL SIZE A B C D Wt. PT22-15 PT22-20 DN15, 20 120 100 130 71 2.7 kg TRAP DISCHARGE CAPACITY IN kg/hr Model Orifice Size DIFFERENTIAL PRESSURE (bar) 0.5 1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.5 10 10.5 PT22-15 PT22-20 2.5 mm 40 80 125 140 180 190 210 225 245 260 265 2.8 mm 65 115 180 215 250 265 280 290 300 ----- ----- 3.2 mm 110 160 210 250 280 ----- ----- ----- ----- ----- ----- Guidelines on use of Capacity Chart • Go to the differential pressure column corresponding to or slightly higher than, but not less than the operating differential pressure at which the trap is to be used. Move vertically downwards and select a suitable model and orifice size. • The selected capacity should be equal to or higher than the condensate load after including a safety factor of 2 to 3. Oversizing is not recommended. • Example - Operating conditions = l) Inlet press. 4bar(g) ll) Back press. 1 bar(g) lll) Condensate load 68 kg/hr. lV) Safety factor 2. Model Selected: PT22-15 • Orifice Size : 2.5 mm • Capacity 140 kg/hr @ a diff. press. of 3 bar HOWTOORDER: PT22-20 DN20 BSP AP ORDERING INFORMATION: 1) Inlet Pressure in bar (g) 2) Back Pressure in bar (g) 3) Operating Temperature in °C 4) Condensate Load in kg/hr 5) Size & Model 6) End Connections AVAILABLE SPARES: SPARE KIT: Valve Pin, Valve Seat, Bracket & Lever Assly. (Op. diff. press. should be specified) Bucket Assly, Set of Gaskets. Local regulations may restrict the use of this product below the conditions quoted. Limiting conditions refer to standard connections only. In the interest of development and improvement of the product, we reserve the right to change the specifications without prior notice. M_ USA - 10 Parsonage Road, Suite 312, Edison, NJ, Tel.: 877-597-TRAP(8727) Fax:1-866-682-1244. ICFmmmwtFmE Email: info@pennantcorp.com Website: www.pennantcorp.com INDIA - S.No. 116 (New), Gat No. 976 (Old), Wadki, Taluka Haveli, Pune - 412 308, INDIA. Tel.: +91 (0) 20 2698 9709, Telefax: +91 (0) 20 2698 9470 § Email: enq@pennantindia.com Website www.pennantindia.com May