Catalog excerpts
GEWINDEFRÄSEN THREAD MILLING Gewindefräsen (zirkular) ● hohe Zylindrizität ● gleichmäßig gefrästes Profil ● einfachere Prüfung ● auch in hochfesten Werkstoffen Thread milling (by circular interpolation) ● high cylindricity ● constant milled profile ● simple checking of thread ● in high strength material
Open the catalog to page 1GEWINDEFRÄSEN (innen) THREAD MILLING (internal) FRÄSERSCHAFT Typ MILLING SHANK Type mit innerer Kühlmittelzufuhr with through coolant supply Cutting edge Ø from Schaftmaterial: Hartmetall (schwingungsarm) Material of shank: Carbide - Giving a good vibration resistance für Schneidplatte for use with Insert Abbildung = rechtsschneidend Picture = right hand cutting version shown Part number Weitere Abmessungen auf Anfrage Further sizes upon request Form Form Bestellhinweis: Fräserschäfte mit beschädigter Schneidplattenaufnahme können durch unseren Reparaturservice instand gesetzt werden....
Open the catalog to page 2Auswahl für Gewinde-Schneidplatten Typ Selection for thread inserts Teilprofil, metrisch Typ 108, 306, 606 Partial profile, metric Type 108, 306, 606 Nenndurchmesser / Nominal diameter Typ 108 / Ds 9,6 R/L 108.0205.01 Vollprofil, metrisch Typ 306 Full profile, metric Type 306 Nenndurchmesser / Nominal diameter Typ 306 / Ds 11,7 306.0815.02 Vollprofil, Whitworth Typ 306, 606 Full profile, Whitworth Type 306, 606 Achtung: Bei Unterschreitung des angegebenen Nenn-Ø wird durch den Nachschnitt des Werkzeugs kein lehrenhaltiges Gewinde mehr erreicht. Attention: Recutting of the milling tool will...
Open the catalog to page 3GEWINDEFRÄSEN (innen) Teilprofil THREAD MILLING (internal) Partial profile SCHNEIDPLATTE Typ INSERT Type Steigung Schneidkreis-Ø Pitch Cutting edge Ø for use with Milling shank Metrisches ISO-Gewinde L = links spiegelbildlich L = left hand version ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Ausführung R oder L angeben State R or L version...
Open the catalog to page 4GEWINDEFRÄSEN (innen) Teilprofil THREAD MILLING (internal) Partial profile SCHNEIDPLATTE Typ INSERT Type Steigung Schneidkreis-Ø Pitch Cutting edge Ø for use with Milling shank Metrisches ISO-Gewinde Abbildung = rechtsschneidend ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Part number Picture = right hand cutting version shown Carbide grades
Open the catalog to page 5GEWINDEFRÄSEN (innen) Vollprofil THREAD MILLING (internal) Full profile SCHNEIDPLATTE Typ INSERT Type Steigung Schneidkreis-Ø Pitch Cutting edge Ø for use with Milling shank Metrisches ISO-Gewinde Abbildung = rechtsschneidend ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Part number Picture = right hand cutting version shown Carbide grades
Open the catalog to page 6GEWINDEFRÄSEN (innen) Vollprofil THREAD MILLING (internal) Full profile SCHNEIDPLATTE Typ INSERT Type Gang pro Zoll Schneidkreis-Ø Thread per inch Cutting edge Ø for use with Milling shank Whitworth-Rohrgewinde nach DIN ISO 228; (259) und 2999 Whitworth pipe thread as per ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Part number Picture =...
Open the catalog to page 7GEWINDEFRÄSEN (innen) Teilprofil THREAD MILLING (internal) Partial profile SCHNEIDPLATTE Typ INSERT Type Steigung Schneidkreis-Ø Pitch Cutting edge Ø for use with Milling shank Metrisches ISO-Gewinde Abbildung = rechtsschneidend Picture = right hand cutting version shown ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Part number Carbide grades
Open the catalog to page 8GEWINDEFRÄSEN (innen) Vollprofil THREAD MILLING (internal) Full profile SCHNEIDPLATTE Typ INSERT Type Gang pro Zoll Schneidkreis-Ø Thread per inch Cutting edge Ø for use with Milling shank Whitworth-Rohrgewinde nach DIN ISO 228; (259) und 2999 Whitworth pipe thread as per ▲ ab Lager / on stock Δ 4 Wochen / 4 weeks ● Haupteinsatzbereich / main recommendation ο bedingt einsetzbar / alternative recommendation ███ unbeschichtete HM-Sorten / uncoated grades ███ beschichtete HM-Sorten / coated grades ███ bestückt/Cermet / brazed/Cermet Abmessungen in mm Dimensions in mm Part number Picture =...
Open the catalog to page 9GEWINDEFRÄSEN (innen) THREAD MILLING (internal) FRÄSERSCHAFT Typ MILLING SHANK Type mit innerer Kühlmittelzufuhr with through coolant supply Schaftmaterial: Hartmetall (schwingungsarm) Material of shank: Carbide - Giving a good vibration resistance für Schneidplatte for use with Insert Abbildung = rechtsschneidend Picture = right hand cutting version shown Part number Weitere Abmessungen auf Anfrage Further sizes upon request Form Form Bestellhinweis: Fräserschäfte mit beschädigter Schneidplattenaufnahme können durch unseren Reparaturservice instand gesetzt werden. Ordering note: Milling...
Open the catalog to page 10All Paul Horn catalogs and technical brochures
-
BOEHLERIT MILLING 2020/2021
149 Pages
-
SOLID CARBIDE MILLS 2020/2021
264 Pages
-
MILLING SYSTEMS 2020/2021
594 Pages
-
DRILLING AND REAMING 2020/2021
198 Pages
-
BOEHLERIT TURNING 2020/2021
193 Pages
-
GROOVING 2020/2021
860 Pages
-
MODULAR HOLDER SYSTEMS 2020/2021
220 Pages
-
JET-WHIRLING
12 Pages
-
Modular grooving systems
44 Pages
-
Turbowirbeln®
4 Pages
-
ROTATING TOOLS
696 Pages
-
CARBIDE GROOVING TOOLS
844 Pages
-
HIGH-PERFORMANCE REAMING
39 Pages
-
high hardness cutting materials
160 Pages
-
Supermini® - mini
328 Pages
-
ROTIERENDE WERKZEUGE
659 Pages
-
HARTMETALL-EINSTECHWERKZEUGE
802 Pages
-
Face grooving system 25A
12 Pages
-
Grooving system 209
4 Pages
-
M382 - Slotting cutter
8 Pages
-
Disc milling cutter M101
16 Pages
-
System DAH25
8 Pages
-
System DS for hard milling
48 Pages
-
System interface 956
8 Pages
-
System 315
4 Pages
-
?-Finish
16 Pages
-
Carbide blanks
36 Pages
-
High polish turning
4 Pages
-
Polygon milling
24 Pages
-
end mill - steel
32 Pages
-
Supermini® Typ 105/110
105 Pages
-
Reaming Tools
31 Pages
-
Drilling
6 Pages
-
Broaching
34 Pages
-
Urma tool
48 Pages
-
DA milling system
22 Pages
-
Multi-Milling System DM
30 Pages
-
Milling Tools
128 Pages
-
Rotating Tools
531 Pages
-
Supermini® & Mini
292 Pages
Archived catalogs
-
thread whirling tool
4 Pages
-
end mill - aluminium
11 Pages
-
solid carbide twist drill bit
4 Pages
-
grooving tool 264
16 Pages
-
thread milling cutter
34 Pages
-
slot milling cutter
14 Pages
-
Milling Catalog 2006-2007
382 Pages