Flanged Products Flanged Products Pro-Bloc
®
(PB) Manifolds
Pro-Bloc
® for sampling applications (10mm bore only)
This manifold range is designed to replace conventional multiple-valve installations where sampling of the processstream is required. This design has been developed to remove a sample directly from the process stream at full
system pressure. All of the options and configurations shown within the standard Pro-Bloc range can be offered
for sampling service by the addition of a customised sampling probe which extends from the pipe flange into the
process stream.
Other flange detail options (reference Box 3 flange
details page 15) Other outlet options (reference Box 4 outlet style page 15)
4. Optional outletsSizeConnection Style 3. Flange details API 6A / ISO 10423(Dimensionally compliant only)FlangeFlangeSizeRating29 1 4 = 1/4” F = Female NPT1 6 = 3/8” M = Male NPT1 8 = 1/2” A = A-LOK
® = 1 13/16”1 2K = 2000 psig0 10 = 5/8” Z = CPI™ 33 = 2 1/16”1 3K = 3000 psig01 12 = 3/4” G =
Swivel gauge adaptor 41 = 2 9/16”1 5K = 5000 psig0 14 = 7/8” 1/2” Female NPT (fitted) 10K = 10000 psig 16 = 1”/0 0M6 = 06mm 3. Flange details DINFlangeFlangeSizeClassDN10 M10 = 10mm M12 = 12mm M14 = 14mm PN6 M15 = 15mm DN15 PN10 M16 = 16mm
Pro-Bloc
® for sampling applications - part numbering
DN20 PN16 M18 = 18mm
SizeClass DN25 PN40 M20 = 20mm In order to specify the addition of a sampling probe to your Pro-Bloc simply add an “S” to
the beginning of the part number i.e. SPB… The probe length in “mm” must be added to
the end of the part number, see below. Due to the internal bore size of standard ASME
flanges probes can only be installed on a range of flanges - please see the attached table.
The probe length must be specified from the raised face to the end of the probe in mm, to the nearest mm.Probes are supplied to suit the insertion length required by the pipeline and thus must be specified by the
customer.
A wide variety of end preparations and support collars are available on request.
Probe strength wake frequency calculations can be carried out against pipeline flow rates on request.
In the event of the required valve configuration not be shown please do not hesitate to contact the factory as
Parker Hannifin IPD offer bespoke customer solutions.
1”1 1/2”150 DN32 PN100 M22 = 22mm DN40
DN50 M25 = 25mm
2”1”1 1/2”300 Note: Contact factory for bore size/outlet connection combinations
2”1”1 1/2”600 2”1”1 1/2”900/1500 2”1”1 1/2”2500
2” When selecting products for specific applications usersshould refer to our notice at the bottom of page 19. IMPOR T ANT NOTES All non wetted parts will be supplied in standard stainless steel for exotic materials. For carbon steel construction trim materials will be supplied instainless steel.
For flange to flange construction when the required flanges are different sizes then specify both sizes in section 3 example: 1st flange 1” pipe (16), raisedface (F), class 900 (900), 2nd flange 1/2” (8), raised face (F), class 900 (900) insert: 16F9008F900. Consult factory for available combinations.Ring type joints (T) CANNOT be supplied for 1/2” & 3/4” class 150 flanges.
St. St. grades 302 and 304 are NOT used in the construction of any of these products.For customer specific options not covered here engineering will allocate a part number at quotation stage.
Certification requirements and customer specifications MUST be provided at enquiry and order stage.For API flange requirements full details must be specified separately.Part number example PBY100B32T2500F Pro-Bloc - Flange by screw - Double Block and Bleed - Block (Ball) Bleed (Industrial needle) Block (Ball) (PBY100) - 316St. St. construction (B) - 2” Pipe flange, Ring type joint, class 2500 (32T2500) - 1/2” female NPT outlet - 1/2” Female NPT vent - Firesafe design andcertified (F), all valves PTFE packed, ball seats PTFE, needle valve metal seated 17-4PH st.st. tips. 16 17
Parker Hannifin Corporation Parker Hannifin Corporation