Group: Parker
Catalog excerpts
p(bar) p(PSID) p(PSID) ∆ ∆ ∆ ∆ > p(bar) p(bar) p(PSID) p(PSID) ∆ ∆ ∆ ∆ > p(bar) p(bar) p(PSID) p(PSID) ∆ ∆ ∆ ∆ > p(bar) p(bar) p(PSID) p(PSID) ∆ ∆ ∆ ∆ > p(bar) p(bar) p(PSID) p(PSID) ∆ ∆ ∆ ∆ >
Open the catalog to page 40CDAB GThreadEmetricFSAE
Open the catalog to page 112Online Particle Detector > Brochure: FDCB321UKOctober 2007 > Fluid condition monitoring size="-1">
Open the catalog to page 251182mm x 155mm x 86mm (7.2 x 6.1Ԕ x 3.4) Dimensions: Weight: 1.3kg (2.9lb) User friendly Abs construction. Stainless Steel hydraulic block. Viton seals. Certifi cation: EMC/RFI Ԗ Materials: EN61000-6-2:2001 EN61000-6-3:2001 0.2% RH typical at 50% RH in one year IP66 rated Moisture sensor stability: 5% RH to 100% RH Operating humidity range: ѱ5% RH (over compensated temperature range of +10C to +80аC) Moisture sensor calibration: 2 to 420 bar (30 to 6,000 PSI) Working pressure: Operating Environment -20C to +60аC (-4F to +140аF) Storage -40C to +80аC (-40F to +176аF) Operating Fluid 0C to...
Open the catalog to page 252Mobile Equipment Power Generation o Earth Moving Machinery o Harvesting o Forestry o AgricultureMonitoring of the hydraulics, enabling the vehicles to function to there best capability under load conditions through pistons, servo valves, control rams and gear pumps. o Wind Turbines o Gearboxes o Lubrication SystemsWith continuous monitoring the optimum level is achieved in the least amount of time. Maintenance o Test Rigs o Flushing StandsTo increase efficiency of your equipment by continuously monitoring the cleanliness level of the hydraulic fluid. Industrial Equipment o Production Plants...
Open the catalog to page 253Pin 4-20mA option connections 0-5v/0-3v option connections 12 3 4567 8 NOT USED RS232 Ground (Pin 5**) Channel A, ISO 4m(c)* Channel B, ISO 6յm (c)* or NAS (if selected) RS232 Receive (Pin 3**) RS232 Transmit (Pin 2**) Moisture sensor channel (if fitted) Channel C, ISO 14m (c)* NOT USEDRS232 Ground (Pin 5**) Channel A, ISO 4յm(c)* Channel B, ISO 6m (c)* or NAS (if selected) RX232 Receive (Pin3**) RS232 Transmit (Pin 2**) Moisture sensor channel (if fitted) Channel C, ISO 14յm (c)* Important Note: It is the responsibility of the end user to ensure that the cables braided screen is terminated...
Open the catalog to page 254Note: The Flow control device will still operate correctly even with the high pressure side at 200bar and the return back to an open system of 0 bar (DP = 200bar) 8 > Parker Hannifin Hydraulic Filter Division Europe FDCB321UK. size="-1">
Open the catalog to page 257IcountPDP1P2High PressureLine SideLow PressureReturn SideOutInFlow Control Device 20.078.2113.2 58.278.2 46.550.0G1/8 ports either side of mounting blockInӔ4 holes 6.60 ThroғOut38.0 Ctrs 90.0 62.080.0 Ctrs49.2 Actuator Manual flow rate adjustable via control knob Mounting Type 4 off mounting holes to suit M6 screws (not supplied) Mounting position Any Weight 1.7kg (3.7lb) Fluid Temperature 5C to +80C (+41аF to 176F) Ambient storage temperature -20аC to +40C (-4аF to +104F) Viscosity range 20cSt to 500cSt (If lower than 20cSt contact Parker) Differential pressure range 5 to 315 bar Maximum...
Open the catalog to page 258The IcountPD may be configured using the IcountPD Setup Utility. For more direct control of the device using its communications protocol, you may also use the Microsoft Windows > HyperTerminal program, but note that this program is not currently supplied with the Windows Vista > Ι operating system. These two ways of communicating with IcountPD are described in the following section. The Communication protocol for the serial communication link is to be used with > Microsoft Windows HyperTerminal . The settings are as follows:Baud rate 9600Data bits 8 Parity None Stop bits 1 Flowcontrol...
Open the catalog to page 259Pressure Transducers and Transmitters >
Open the catalog to page 281The CompletePerformer range utilises ASIC technology (Application Specific Integrated Circuit) programmable software. > AC/DC display unit (DDU1002) 2 > Parker Hannifin Hydraulic Filter Division Europe FDHB240UK. size="-1">
Open the catalog to page 282Maximum OverloadPressure Pressure ranges: x 6.0 (150 bar) x 2.5 (150 Bar) x 2.5 (250 bar) x 4.0 (1000 Bar) x 2.5 (1000 Bar) x 1.5 (1000 Bar) > 1 / > 4 ( > 1 / > 4 BSP) with ED seal.All thread forms and sensor interfaceare made from 1.4301 stainless steel.Non standard threads - contactParker CMC 25, 60, 100, 250, 400, 600 bar. IEC 60068-2-6: +/- 5mm/10Hz...32Hz 200m/s Pressure Tolerance Specifications:Vibration resistance: > 2 / 32Hz...2kHz Rating Installation: 2560100 250 400 600 Spanner size 22A/F. Max. (recommended) tightening torque = 30Nm. Weight: 200 - 230g Lifespan: Functional temp...
Open the catalog to page 283AE United Arab Emirates, HK ֖ Hong Kong SL Slovenia, Novo Mesto Tel: +386 7 337 6650 Abu Dhabi Tel: +971 2 67 88 587 Tel: +852 2428 8008 HU ֖ Hungary, Budapest Tel: +36 1 220 4155 SK Slovakia AR ֖ Argentina, Buenos Aires Tel: +54 3327 44 4129 See Czech Republic IE Ireland, Dublin TH ֖ Thailand, Bangkok Tel: +662 717 8140 AT Austria, Wiener Neustadt Tel: +43 (0)2622 23501-0 Tel: +353 (0)1 466 6370 IN ֖ India, Mumbai TR Turkey, Merter/Istanbul Tel: +90 212 482 91 06 or 07 AT ֖ Austria, Wiener Neustadt Tel: +91 22 6513 7081-85 (Eastern Europe) Tel: +43 (0)2622 23501 970 IT Italy, Corsico (MI)...
Open the catalog to page 308All Parker Hydraulic and Industrial Filtration Divisio catalogs and technical brochures
-
GMF iprotect®
8 Pages
-
10MFP Series
8 Pages
-
12CS Series
6 Pages
-
Hydraulic_Filtration_Solutions
38 Pages
-
Parker icount Oil Sampler
12 Pages
-
Condition Monitoring
80 Pages