PLS 2 - Pacific Laser Systems - #2

Text version of the page

CHECK LEVEL CHECK PLUMB WARRANTY SPECIFICATIONS Light source: Semiconductor laser diode 635-670 nm, visible Working range: +/- 100 feet (outdoor w/detector) Accuracy: <1/8” @ 30 Feet (outdoor w/detector) (<3mm @ 10 meters) Leveling: Automatic Leveling range +/- 6o Power supply: 3AA batteries alkaline or rechargeable Operating time: +25 hours continuous use with single beam; 12.5 hours both beams Operating temp: 0o F to 122o F (-18o C to 50o C) Storage temp: -40 F to 158o F (-40o C to 70o C) Indicator: Green light: ON Red light: EXCEEDS TILT/ TILT OVERRIDE #4 Amber light: BATTERY LOW Flashing: pulse beam- PLS2E Environment: Water resistant; not submersible Dimensions: 2” x 2-7/8” x 3-3/8” Weight: 10 oz.(.28kg) (including batteries) We recommend that you check your PLS2 periodically in order to assure its accuracy. TO CHECK LEVEL: Choose two interior walls approximately 15’-0” apart (see Fig. 1). You can use 2 x 4s for targets. Turn on the PLS2 to setting #1 (level). With the PLS2 six inches away from and facing target #1, carefully mark the center of the line. Label this mark A1. Swivel the laser 180º and mark the center of the line on target #2. Label this mark B1. Move the PLS2 six inches away from and facing target #2. Carefully mark the center of the line. Label this mark B2. Swivel the laser 180º and mark the center of the line on target #1. Label this mark A2. Now measure the distance between A1 and A2, B1 and B2. If the distances are the same, the laser is in calibration. If the difference between the two sets of marks is greater than 1/8”, the laser is out of calibration. Choose a door jamb with 8’-0” clear on each side of the door. Turn on your PLS2 laser to setting #2 (plumb). With your laser at point A, make two marks on the floor: the first at 8’-0” from point A centered on door header above (mark this point B), the second 16’-0” from point A (mark this point C). Without moving the laser, make a third mark on the door header (mark this point D). Move the laser to point C, exactly align the beam with point B, and notice where the beam falls at point D. If it is within a “light” 1/16” of point D, the laser is in calibration. This product is warranted by PLS · Pacific Laser Systems to the original purchaser to be free from defects in material and workmanship under normal use for a period of one year from the date of purchase. During the warranty period, and upon proof of purchase, the product will be repaired or replaced (with the same or similar model at our option), without charge for either parts or labor, through PLS. The purchaser shall bear all shipping, packing and insurance costs. Upon completion of the repair or replacement, the unit will be returned to the customer, freight prepaid. The warranty will not apply to this product if it has been misused, abused or altered. Without limiting the foregoing, battery leakage, dents or gouges to the plastic housing, broken optic windows, damage to the switch/LED membrane are presumed to result from misuse or abuse. Tampering with or removal of the caution or certification labels voids this warranty. Neither this warranty nor any other warranty, express or implied, including implied warranties of merchantability, shall extend beyond the warranty period. No responsibility is assumed for any incidental or consequential damages. This warranty gives you specific legal rights, and you may have other rights which vary from state to state. A D C • • B• Target #1 • Target #2 PALM LASER PLS2 ¤ PALM LASER PLS2 ¤ PLS Lab Technicians A1 + A2 B1 + B2 - 15’ If level & plumb are within specification, square will be in specification. PULSE PLS2E W/DETECTOR AVERAGE DISTANCE AND HORIZONTAL-VERTICAL LINE LENGTH USING PLS LD LASER DETECTOR DISTANCE LINE LENGTH ACCURACY 30ft 75ft 1/ 8” 50ft 75ft 3/ 16” 100ft 125ft 3/ 8”