Catalogs >
ORIENTAL MOTOR >
Reversible Motors

Reversible Motors
25Pages

Catalog excerpts

Reversible Motors ˾Features b Optimal for Bi-Directional Operation These are 30 minutes rated motors that can change directions instantaneously. They are designed for applications where reversal of direction is frequently required. ✽ 30 minutes rating: The motors may be operated continuously for 30 minutes, but depending on operating conditions (intermittent operation, etc), they can be operated for more than 30 minutes. ˾Safety Standards and CE Marking Standards UL 1004 UL 2111 CSA C22.2 No.100 CSA C22.2 No.77 Certification Body Standards File No. E64199 (1 Wȁ6 W Type) E64197 (15 Wȁ90 W Type) Conform to EN/IEC Standards 2005010401150787 (Single-Phase 1 W Type) 2003010401091525 (Single-Phase 6 W Type) 2003010401091522 (Single-Phase 15 Wȁ90 W Type) b When the motor is approved under various safety standards, the model name on the nameplate is the approved model name.

Open the catalog to page 1

Brake Pack SB50W (Sold separately) Equipped with instantaneous stopping functions, thermal protector open detection functions. Flexible Couplings (Accessories) Motor AC Power Supply Capacitor Cap✽ (Included) Insulating cap for capacitor terminal section. Capacitor (Included) ȜExample of System Configuration (Body) (Sold separately) Motor (Pinion Shaft) 4RK25GN-CW2E Long Life/Low Noise Mounting Bracket GN-S Gearhead 4GN25S SOL4M5 Reversible Motors Gearheads (Sold separately) Induction Motors Mounting Brackets (Accessories) Right-Angle Gearheads (Sold separately) ˾System Configuration b The...

Open the catalog to page 2

˾General Specifications of Motors b 1 W Type Item Dielectric Strength Sufficient to withstand 1.5 kV at 50 Hz or 60 Hz applied between the windings and the frame for 1 minute after rated motor operation under normal ambient temperature and humidity. Temperature Rise Insulation Resistance 100 M⍀ or more when 500 VDC megger is applied between the windings and the frame after rated motor operation under normal ambient temperature and humidity. Temperature rise of windings are 75˚C or less measured by the resistance change method after rated motor operation under normal ambient temperature and...

Open the catalog to page 3

Reversible Motors ˾Specifications – 30 Minutes Rating Model Lead Wire Type Round Shaft Type Rated Speed Current Starting Torque Rated Torque A 0.120 0.125 0.090 0.095 0.066 0.069 Reversible Motors Pinion Shaft Type Output Power Induction Motors (Gearhead sold separately) b Values shown for rated torque and starting torque are measured for operation without the friction brake installed. b The J and U at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the...

Open the catalog to page 4

˾Permissible Overhung Load and Permissible Thrust Load Motor (Round shaft type) ➜ Page 107 Gearhead ➜ Page 107 ˾Permissible Load Inertia J for Gearhead ➜ Page 107 ˾Dimensions (Unit = mm) Mounting screws are included with gearheads. Protective Earth Terminal M4 Protective Earth Terminal M4 Motor Leads 300 mm Length UL Style 3266, AWG22 The mass and motor's dimensions (excluding the shaft section) are the same as those of the pinion shaft type. ␾5Ϫ0.012 (h7) ȣ Shaft Section of Round Shaft Type ȣ Lead Wire Type Protective Earth Terminal M4 Detail Drawing of Protective Earth Terminal ȣ...

Open the catalog to page 5

Reversible Motors Induction Motors Lead Wire Type (Gearhead sold separately) Model Upper Model Name: Pinion Shaft Type Lower Model Name ( ): Round Shaft Type Terminal Box Type Dimension ባ Lead Wire Type Dimension ቢ Current Starting Torque Rated Torque Rated Speed b Values shown for rated torque and starting torque are measured for operation without the friction brake installed. b The J, U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model...

Open the catalog to page 6

˾Gearmotor – Torque Table bGearheads and decimal gearheads are sold separately. Ⅵ bEnter the code that represents the terminal box type "T" in the box (Ⅺ) within the model name. bEnter the gear ratio in the box (Ⅺ) within the model name. indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite bA colored background direction. bThe speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 - 20% less than the displayed value, depending on the size of the...

Open the catalog to page 7

Mass: Motor 0.9 kg Gearhead 0.4 kg 7 b Specify the type of the capacitor to be included by entering J, U or E in the box Ⅵ (Ⅺ) within the model name. Enter the gear ratio in the box (Ⅺ) within the model name. b Use cable with a diameter of ␾8 ȁ ␾12 mm. The mass and motor's dimensions (excluding the shaft section) are the same as those of the pinion shaft type. Can be connected to GN pinion shaft type. Protective Earth Terminal M4 (Lead Wire Type Only) Reversible Motors ȣ Shaft Section of Round Shaft Type Induction Motors Gearhead Model ȣ Capacitor (Included with the motors) ȣ Capacitor...

Open the catalog to page 8

Reversible Motors 1W (Gearhead sold separately) ˾Specifications – 30 Minutes Rating Model Lead Wire Type Pinion Shaft Type 3RK15GN-AW2J Output Power Round Shaft Type Single-Phase 200 Single-Phase 220 Single-Phase 230 Rated Speed r/min 1200 1450 b Values shown for rated torque and starting torque are measured for operation without the friction brake installed. b The J, U and E at the end of the model name indicate that the unit includes a capacitor. These letters are not listed on the motor nameplate. When the motor is approved under various safety standards, the model name on the nameplate...

Open the catalog to page 9

Speed r/min Motor/ Gearhead Gear Ratio Induction Motors bGearheads and decimal gearheads are sold separately. bEnter the gear ratio in the box (Ⅺ) within the model name. bA colored background indicates gear shaft rotation in the same direction as the motor shaft, while the others rotate in the opposite direction. bThe speed is calculated by dividing the motor's synchronous speed (50 Hz: 1500 r/min, 60 Hz: 1800 r/min) by the gear ratio. The actual speed is 2 - 20% less than the displayed value, depending on the size of the load. bTo reduce the speed beyond the gear ratio in the table, attach...

Open the catalog to page 10