catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
P. 49
P. 50
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Pillow block, Planetary gearmotor, Damper, Radial ball bearing, Worm gear reducer
Text version of the page
GEARBOXES
EType Right Angle Helical Reducers
Heavy Duty 6mm 30mm Bores 1:1 - 40:1
T TECHNICAL❶❷❸❹❹➎➎➏
❶ ❹ Case: Bearings: AA15 red anodised aluminium (6082-T6). Steel single row radial ball bearing with 2RS rubber shields. ❷ ❸ ➎ Input Gear: Output Gear: Circlips: DIN 471 C60 or C75 Steel For 1:1 - 5:1 ratios hardened alloy steel 655M13 (14NiCr14)or 805M20 (21NiCrMo2) helical gear For 8:1 - 40:1 hardened alloy steel 655M13 (14NiCr14) or 805M20 (21NiCrMo2) worm gear. For 1:1 - 5:1 ratios Hardened Alloy Steel 655M13 (14NiCr14) or805M20 (21NiCrMo2) helical gear. For 8:1 - 40:1 E20 & E30 Aluminium Bronze (CA104 / AB2) wormwheel gear. For 8:1 - 40:1 E40, E50 & E60 Aluminium Bronze (CA104 / AB2) wormwheel with Alloy Steel 214M15 shaft. ➏ Pressure Plug: Backlash: Figures give are at output. Standard backlash ? 1. Low backlash A version1 ⁄
8 BSP Plug. Gearboxes are greased for life. Refilling is only requiredwhen boxes are disassembled for refurbishment. Not fitted on E20 and E30. ≤ 30 arc mins. Motor Fitting Inputs: Output Shafts: Thrust & Overhung Loads: Specials: Available from Ondrives are not only an extensive range of standard designreduction units but modifications to this range are available. To find out more please contact the Ondrives Technical Department. Single & double output shafts are available in 303 stainless steel. Seeopposite for details. Special flange and input required, add 35% to cost. See page 16for details on motor frame sizes. Certain restrictions may apply if the size of motor required is too large. For further information on prices and delivery, please contact the Ondrives Technical Department. Based on an input speed of 1000rpm taking full torqueload and combined thrust and overhung load. Keyways and Bores: All bores are toleranced to H7ISO 286 as standard. Keyways allowuse of parallel DIN 6885 keys with sliding fit. Tolerances may vary due to manufacturing processes.
+44 (0)1246 455500 +44 (0)1246 455522