DANEO 400 - Hybrid signal analyzer for power utility automation systems
16Pages

{{requestButtons}}

Catalog excerpts

DANEO 400 - Hybrid signal analyzer for power utility automation systems - 1

DANEO 400 Hybrid signal analyzer for power utility automation systems

Open the catalog to page 1
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 2

DANEO 400 – hybrid measurement DANEO 400 is a hybrid measurement system that records and analyzes all conventional signals (voltages, currents, hard wired binary status signals) and messages on the communication network in a digital substation. It measures signals from both of these worlds and can provide information to assess their proper coordination. With this device you can easily keep track of what is going on in the substation by obtaining information on the operational status and communication. Easy configuration and control Easily configure and control one or more DANEO 400 units...

Open the catalog to page 2
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 3

system Fields of application DANEO 400 is a useful tool that covers the whole life-cycle of a protection automation and control (PAC) system. Maintenance/ Change DANEO 400 can be used in all kinds of different PAC systems and network topologies: > Hybrid substation with conventional signals and network communication > Local area network (LAN) in local substations > Wide area network (WAN) between substations > Redundancy network topologies (e.g. HSR and PRP) Main use cases > Fault recording (classical and hybrid) > Verification of IEC 61850 communication > Supervision of network traffic >...

Open the catalog to page 3
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 4

One device - multiple use cases Fault Recording (classical and hybrid) The occurrence of a malfunction in a PAC system is often unpredictable. Problems occur infrequently and under conditions which are not always known. When they do occur it is critical to resolve such issues. In troubleshooting you often need to react to situations without any preparation and you have to improvise without access to the full documentation of the system. DANEO 400 helps you to find out what may be causing the malfunction. DANEO Control or Web Interface Unattended operation The device works unattended in...

Open the catalog to page 4
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 5

Verification of IEC 61850 communication The IEC 61850 communication is a mission critical part of a PAC system. DANEO 400 supports you to easily verify, proof and document that your protection and control devices are working and communicating properly. The description of the communication system in the standardized IEC 61850 substation configuration language (SCL) format serves as the basis for the verifications. It is verified that the IEC 61850 server of all IEDs are available and the substation network traffic is actually present on the communication network as defined. As devices are...

Open the catalog to page 5
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 6

One device – multiple use cases Supervision of network traffic During the normal operation of a PAC system, it is recommended to supervise the IEC 61850 network traffic is supervised so that any issue are detected immediately. The supervision is based on the SCL definition and constantly evaluates all network packets of GOOSE messages and Sampled Values streams. The DANEO 400 detects abnormalities in the network traffic and automatically logs all events with the corresponding detailed information (e.g. lost samples, GOOSE timing problems, PTP time synchronization issues…). The event...

Open the catalog to page 6
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 7

Network performance assessment The correct functioning of the communication network is an essential precondition for the optimal performance of a PAC system. Consequently, the performance and load of the communication network needs to be measured and assessed on its own. Depending on the communication architecture and technologies deployed, different approaches are applicable. DANEO 400 measures and assesses the transfer of status information (e.g. GOOSE messages) within a local substation network or between substations. All involved devices are configured and controlled with the DANEO...

Open the catalog to page 7
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 8

DANEO Control – data acquisition and analysis The innovative DANEO Control is the PC software to easily control your DANEO 400 measurement system and analyze your recordings. It is divided into an Acquisition and Analysis workspace. All configurations and results can be saved in files, printed or stored in PDF/RTF format. Data acquisition In the Acquisition workspace you configure your measurement devices and IEDs of the system under test. You can import IED configurations from SCL files and find GOOSE and SV orphans on the network. The whole test setup is visualized in a network diagram....

Open the catalog to page 8
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 9

Data analysis In the Analysis workspace you can analyze your recordings, view all supervisor events, and assess the performance of the substation network. It is easy to find and select the recordings and supervisor events on the time line. The data is collected from your devices or from local folders. If recordings are too large, just crop it for analyzing. Simply export your recordings into COMTADE and PCAP files for analyzing the data with other tools. Analysis tools: Time Signal Analysis All recorded signals are available in an aggregated and time-aligned view for analysing the results....

Open the catalog to page 9
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 10

Operating options Web interface The DANEO 400 has a built-in web interface. Certain functions of a single device can be accessed by simply connecting with a web-browser. The supported feature set focuses on functions related to the traffic on the communication network. The device status can be checked and available recordings can be downloaded for further analysis. It is also possible to publish up to three Sampled Values streams. Flexible housing The housing of the DANEO 400 is very flexible. It can be configured for different working positions by rotating and moving the device handle. For...

Open the catalog to page 10
DANEO 400 - Hybrid signal analyzer for power utility automation systems - 11

Accessories EXB1 binary I/O extension unit The EXB1 extends the I/O capabilities of the DANEO 400. The EXB1 units are connected to the DANEO 400 main unit via the extension interfaces. Technical specifications Binary inputs Binary outputs EtherCAT® extension interfaces; daisy chaining of multiple units possible EXB1 binary I/O extension unit PTP grandmaster clock In some cases a time synchronization of the involved DANEO devices is a must (e.g. distributed recording with multiple units). Dedicated PTP grandmaster clocks are required if the PTP protocol is not available yet on the...

Open the catalog to page 11

All OMICRON electronics catalogs and technical brochures

  1. MCT 085

    2 Pages

  2. PDL 650

    8 Pages

  3. CPC 100

    44 Pages

  4. InSight

    4 Pages

  5. MONTESTO 200

    16 Pages

  6. ISIO 200

    8 Pages

  7. CMControl R

    12 Pages

  8. CMControl P

    8 Pages

  9. CMS 356

    2 Pages

  10. IEDScout

    8 Pages

  11. CMA 156

    1 Pages