Process Flow Meter Calibration System - 24 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

Catalogue excerpts

Calibration is a Comparison between the reading of a Device (Unit under Test) and that of a Standard. The process which establishes this relationship is a set of interrelated measurements and set of operations which provide the Comparison. After flow meters are manufactured / procured, they need to be calibrated before being sent out into the field. Most flow meter manufacturers have their own flow meter calibration facilities for performing this initial calibration. Calibration of flow meters enables us to optimize their utility, with the result that the Uncertainty between the actual measurement...

 Open the catalogue to page 2

PROCESS FLOW METER CALIBRATION SYSTEM FLOCAL SERIES Flow meter measures the rate of flow of fluid which passes through it. Flow meters are used in wide variety of applications where accurate flow measurements are critical in various sectors like Energy, Power, Refineries, Utilities, Water Management, Aerospace, Pharmaceutical Industry etc. In critical applications like these, it's important to Calibrate the Flow Meters to enable make reliable measurements. Regular Calibrations assure you that the Flow Meter's Measurements are as accurate as their specifications. Even the most rugged Flow Meters...

 Open the catalogue to page 3

3D VIEW OF FLOCAL SYSTEM COMPARISON METHOD

 Open the catalogue to page 4

Specifications / Features 'PROCESS' FLOW METER CALIBRATION SYSTEM Nofe: Gravimetric Calibration can be performed up to 6,000 Liters volume on the basis of 1 minute (60 Seconds) campaign (i.e. Flow rate 6000 LPM). For volume higher than 6,000 Liters (for e.g. flow rates higher than 6,000 liters I minute) Gravimetric Calibration Campaign time will be varied according to the set flow rate.

 Open the catalogue to page 5

3D VIEW OF FLOCAL SYSTEM AUTOMATIC SYSTEM

 Open the catalogue to page 6

Specifications / Features 'PROCESS' FLOW METER CALIBRATION SYSTEM Nofe: Gravimetric Calibration can be performed up to 12,000 Liters volume on the basis of 1 minute (60 Seconds) campaign (i.e. Flow rate 12000 LPM). For volume higher than 12,000 Liters (for e.g. flow rates higher than 12,000 liters I minute) Gravimetric Calibration Campaign time will be varied according to the

 Open the catalogue to page 7

WATER METER CALIBRATION TEST BENCH SYSTEM WATCAL SERIES It is every one's responsibility to save water, which is a precious commodity. After all, out of 100% of the Worlds' Water resource, only 3% of the water is usable, this imposes moral responsibility to precisely use this natural & scarce resource. Nag man Designed & introduced 'WATCAL' - Water Meter Calibration Systems, for Calibrating the Accuracy of: Domestic Water Meters, typically in sizes Industrial / Bulk Water Meters, typically in sizes In accordance with the Standard ISO4064/3, BIS 779 Domestic Water Meters and Bulk Water Meters are...

 Open the catalogue to page 8

3D VIEW OF WATCAL SYSTEM COMPARISON METHOD

 Open the catalogue to page 10

Specifications / Features WATER METER CALIBRATION TEST BENCH SYSTEM

 Open the catalogue to page 11

Specifications / Features WATER METER CALIBRATION TEST BENCH SYSTEM

 Open the catalogue to page 13

3D VIEW OF WATCAL SYSTEM VOLUMETRIC METHOD

 Open the catalogue to page 14

Specifications / Features WATER METER CALIBRATION TEST BENCH SYSTEM

 Open the catalogue to page 15

3D VIEW OF WATCAL SYSTEM

 Open the catalogue to page 16

Specifications / Features WATER METER CALIBRATION TEST BENCH SYSTEM

 Open the catalogue to page 17

WATER METER CALIBRATION TEST BENCH SYSTEM WATCAL 50300 SERIES (Contd.) Gravimetric Calibration can be performed up to 12,000 Liters volume on the basis of 1 minute (60 Seconds) campaign (i.e. Flow rate 12000 LPM). For volume higher than 12,000 Liters (for e.g. How rates higher than 12,000 liters/minute) Gravimetric Calibration Campaign time will be varied according to the set flow ** Volumetric Method: Measuring Capacity By using One Diverter System & 2 Nos. of Large Volumetric Tanks (2000 - 3000L) (Cascaded Double Decker). Once Maximum Level (5000 L) reaches in Tank 1, the PROXIMITY SWITCH triggers...

 Open the catalogue to page 18

FLUID FLOW CALIBRATION LABORATORY Nagman's Centre for Calibration is the first Calibration Laboratory in India to be Accredited as per ISO/IEC 17025:2005 being managed by dedicated, highly qualified, trained & Competent Experts in the field of Calibration to take care of all types of Customer's specific requirements & provide solution. Centre for Calibration is a unit of Nagman Instruments & Electronics Private Ltd., Chennai. This Calibration Lab is Accredited by NABL India to provide Calibration Services as per ISO/IEC 17025:2005 Standards. The Team consists of Qualified & NABL Empaneled Assessor,...

 Open the catalogue to page 19

DOMESTIC GAS METER CALIBRATION SYSTEM BELL PROVER METHOD GASCAL SERIES Calibration method for any particular flow meter is governed by the meter type, the ranges of flow and flow conditions, pressure, temperature and the accuracy of calibration required. In general all the methods have analogies with the liquid methods. The main difference between the calibration of a gas flow meter and a liquid device is the compressibility of the fluid. When calibrating a gas flow meter the temperature, pressure and hence volume of gas measured by the standard will be different from that at the device under...

 Open the catalogue to page 20

GASCAL SYSTEM BELL PROVER

 Open the catalogue to page 21

DOMESTIC GAS METER CALIBRATION SYSTEM BELL PROVER METHOD The 'Calibration Standard' of the Test system is "Bell Prover", which is considered a Primary (Calibration) Standard to Test & Calibrate Domestic Gas Meters. The device is ideal for OEMs, Calibration Laboratories & Calibration Service Providers. The Test System with Bell Prover of Capacity (100L) will effectively cover Vey Low (Q min - 0.016 mVhr.) to Maximum (Q max - 4 mVhr.) Flow Rates. Accuracy: 0.5% F.S. It can test Q-max, 0.2Q-max, and Q- min separately as per different gas meters. Bell Prover has built-in Pump to deliver the Air at...

 Open the catalogue to page 22

DOMESTIC GAS METER CALIBRATION SYSTEM BELL PROVER METHOD The 'Calibration Standard' of the Test system is "Bell Prover", which is considered a Primary (Calibration) Standard to Test & Calibrate Domestic Gas Meters. The device is ideal for OEMs, Calibration Laboratories & Calibration Service Providers. The Test System with Bell Prover of Capacity (200L) will effectively cover Vey Low (Q min - 0.016 m7hr.) to Maximum (Q max - 4 mVhr.) Flow Rates. Accuracy: 0.5% F.S. It can test Q-max, 0.2Q-max, and Q- min separately as per different gas meters. Bell Prover has built-in Pump to deliver the Air at...

 Open the catalogue to page 23

All Nagman Instruments & Electronics (P) Ltd. catalogues and technical brochures

  1. Flow Meters

    8 Pages

    En
  2. Test Bench

    24 Pages

    En
  3. Product Flier

    4 Pages

    En
  4. GCL & GCH Series

    2 Pages

    En
  5. HHP Series

    2 Pages

    En
  6. PHP2 Series

    2 Pages

    En
  7. Model BBS-VH

    2 Pages

    En
  8. Model BBSD

    2 Pages

    En
  9. Model 1500HN

    2 Pages

    En
  10. Model 1200HN

    2 Pages

    En
  11. Model MTC650

    2 Pages

    En
  12. Model MP650

    2 Pages

    En
  13. Model 650H

    2 Pages

    En
  14. Model 350H

    2 Pages

    En
  15. Model MP40R

    2 Pages

    En