Linear modules - 50 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

  13. P. 40

  14. P. 50

Catalogue excerpts

Linear and Motion Solutions Linear Modules

 Open the catalogue to page 1

Product overview Product description Setting, performances, characteristics, application and combination examples Linear module with toothed drive belt - roller guide - single, double or long carriage Linear module with toothed drive belt - roller guide - single, double or long carriage Linear module with toothed drive belt - roller guide - single, double or long carriage Linear module with toothed drive belt - roller guide or recirculating ball guides - single, double or long carriage Linear module with toothed drive belt with or without cover band - roller guide or recirculating ball guide -...

 Open the catalogue to page 2

Product overview Basic-Line AXN AXN 45-Z Toothed belt Toothed belt Toothed belt Toothed belt Max. dynamic working load (N) Profile cross section w x h (mm) Drive Repeat accuracy (mm) Max. speed (m/s) Guide system Max. total length overall (m) in one part - longer version of 8 m upon request Max. loads and dynamic working loads dependent on guide system

 Open the catalogue to page 3

Basic-Line AXN Product description High performance and low costs are the outstanding features of this model range. If individual module or multi system: Depending on customers‘ requirements various combinations are possible. Toothed belt For space and cost reasons the modules are equipped with toothed belt tension located below the table plate. By positive belt retainer the toothed belt is getting tension and laterally security. Roller guide The characteristic features of the roller guide are cost-saving, nearly maintenance-free concomitant with highperformance. Resistance to soiling and smooth...

 Open the catalogue to page 5

Basic-Line AXN Product description Integrated wiper brushes The actuator profile of the basic line modules is covered on the upper side by the circular toothed belt. Wiper brushes integrated in the head covers prevent effectively lager dirt particles from penetrating into the profilee. 1 Assembly and fixation of the actuator Two longitudinal T-slots in the table plates (thread at AXN 45) make it easily possible to install the moving parts. By end-to-end T-slots at the bottom and on either side of the actuator a universal installation of the module is possible. In this application adequate swivelling...

 Open the catalogue to page 6

Actuator with toothed belt and roller guide Lubricating nipple Stroke calculation; using distance and safty overrun Values In brackets for long carriage, * Motor connection see chapter Drive adaption

 Open the catalogue to page 7

Loads and load moments* Roller guide * The dynamic load of the guide system is based on a nominal Values in brackets for execution with long carriage (254 mm) Technical data Actuation Toothed belt 16 AT5 Max, dynamic working load 325 K Feed rate per rotation 100 mm Geometrical moment of Inertia ly 21,7 cm4 Geometrical moment of Inertia lz 22,5 cm4 Rust-resistant version available

 Open the catalogue to page 8

Actuator with toothed belt and roller guide Stroke calculation: using distance and safty overrun Values In brackets for long carnage. * Motor connection see chapter Drive adaption

 Open the catalogue to page 9

Loads and load moments* Roller guide * The dynamic load of the guide system is based on a nominal Values in brackets for execution with long carriage (350 mm) Technical data Actuation Toothed belt 32 AT5 Max, dynamic working load 650 N Feed rate per rotation 150 mm Geometrical moment of Inertia ly 80,2 cm4 Geometrical moment of Inertia lz 89,2 cm4 1) major length upon request Rust-resistant version available,

 Open the catalogue to page 10

Actuator with toothed belt and roller guide Stroke calculation: using distance and safty overrun Values in brackets for long carriage, * Motor connection see chapter Drive adaption

 Open the catalogue to page 11

Loads and load moments* Roller guide * The dynamic load of the guide system is based on a nominal Values in brackets for execution with long carriage (460 mm) Technical data Actuation Toothed belt 32 AT1C Max, dynamic working load 1450 K Feed rate per rotalon 180 mm Geometrical moment of Inertia ly 198,5 cm4 Geometrical moment of Inertia lz 207,4 cm4 1) major length upon request Rust-resistant version available

 Open the catalogue to page 12

Actuator with toothed belt and roller guide Lubricating nipple Stroke calculation: using distance and salty overrun Values In brackets for long carriage, * Motor connection see chapter Drive adaption

 Open the catalogue to page 13

Basic-Line AXN AXN 100-Z Load and load moments* Roller guide 52.16 Load s(N) * The dynamic load of the guide system is based on a nominal liftetime of 54.000 km. Values in brackets for execution with long carriage (580 mm) Technical datal Max. speedt max. 10 m/s Repeating accuracy ± 0,05 mm/m Actuation Toothed belt 50 AT10 Max. dynamic working load 2500 N Feed rate per rotation 230 mm Idle-running torque 3 Nm Moment of inertia 14 kgcm2 Max. length overall 1) 6 m (8m)1) Geometrical moment of inertia IY 343 cm4 Geometrical moment of inertia IZ 465 cm4 1) 8m in one piece dependent on availability Mass...

 Open the catalogue to page 14

Basic-Line AXNPlus Product description The new range of AXNP modules is a further development our our successful AXN modules with toothed drive belt. These units have been developed especially for quick handling and positioning functions. If individual or multi system – depending on customers’ requirements various combinations are possible, even a combination with the AXN module range is possible. Toothed drive belt AT-type belt, reinforced with steel cords, allows transfer of large drag forces and guarantees a long liftime. The belt tension is located in the crosshead. Roller guide / Rail guide...

 Open the catalogue to page 15

Basic-Line AXNPlus Product description Dirt protection The actuator profile of the basic line modules AXNP contains a cover band which covers the profile completely on the upper side. Therefore, dirt particles can not enter into the actuator. In additon, wiper brushes integrated in the head covers prevent effectively larger dirt particles from penetrating into the profile. Of course all actuators can also be delivered without cover band. Assembly and fixation of the actuator By roll-in T-slots, fastening shoulder and connection plates a universal installation of the module is possible. In this...

 Open the catalogue to page 16

All Nadella catalogues and technical brochures

  1. LET'S MOVE.

    6 Pages

    En
  2. AXC 60

    2 Pages

    En
  3. Flyer

    2 Pages

    En
  4. Let'sMove

    6 Pages

    En
  5. Cam followers

    22 Pages

    En
  6. Needle Bearings

    230 Pages

    En
  7. Company Brochure

    12 Pages

    En
  8. Telescopic-Line

    77 Pages

    En
  9. Adjusting nuts

    18 Pages

    En
  10. Linear Module AXN

    33 Pages

    En