AG-ESS DRILL? AG-ES DRILL - 4 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

Catalogue excerpts

Standard Drilling Conditions AG-ESSHUIU AG-ESS DRILLS A-t-ten-tion on using the drilling condition tables I Adjust drilling condition according to the rigidity of machine or work clamp state. I The table values are for drilling with water soluble cutting fluid. I Provide sufficent amount cutting fluid to the cutting point and in the flute. I In non water soluble cutting fluid, reduce the rotation and feed by 20% I Use the table values for drilling depths under 3xD. I When for hole depth more then 3xD, reduce the rotation and feed by 20% I When for hole depth more then 3xD deep, add step seediing. I However, a work material and drilling condition to Chip removal may be worse. In that case, add A even if drilling depth 3xD is as follows. I In step feed, return to the entrance hole. I Step feed interval is about 0.5^1 xD. In small diameter, about 0.2^0.5xD . I Adjust the drill run out to 0.02mm or less. I Ues a collet chuck, milling chuck. I After grinding please lower drilling condition. The new alloy HSS drill is approached to the carbide drill. AG-ES DRILL

 Open the catalogue to page 1

Realize high-speed and high-feed which is approached to the carbide drill. AG-ESS DRILL AG-ESS / AG-ES The chip proves the good quality of sharpness. H igh efficient drilling like the carbide dril I It is high-speed/longer tool life/high reliability/low cost. I High alloy HSS of new development new AG coating best match. I Although being the melting HSS, longer tool life it exceeds the powder HSS I It realizes high speed drilling equal to carbide drill with reliability only by HSS Competitor powder HSS coated drill compared to 30% longer tool life AGESS «±B*nmm maivuNUT. Competitor Competitor It...

 Open the catalogue to page 2

All NACHI-FUJIKOSHI CORP. catalogues and technical brochures

  1. GSX MILL VL Series

    16 Pages

    En
  2. SG Drill Series

    12 Pages

    En
  3. SG Flat Drill

    4 Pages

    En
  4. AQUA Drill Series

    48 Pages

    En
  5. NV-Pro

    2 Pages

    En
  6. FlexGui

    2 Pages

    En
  7. MZ Series

    4 Pages

    En
  8. Robot

    30 Pages

    En
  9. SRA100B/100J

    2 Pages

    En
  10. SRA100H/SRA133HL

    2 Pages

    En
  11. FLEXhand

    2 Pages

    En
  12. FD Controller

    2 Pages

    En
  13. MC350

    2 Pages

    En
  14. SC400L

    2 Pages

    En
  15. SC500

    2 Pages

    En
  16. SC700

    2 Pages

    En
  17. VS05G/VS05LG

    2 Pages

    En
  18. MC12S

    2 Pages

    En
  19. MC20/MC10L

    2 Pages

    En
  20. MC35/50/70

    2 Pages

    En
  21. MR20/20L

    2 Pages

    En
  22. MR35/50

    2 Pages

    En
  23. LP130/180-01

    2 Pages

    En
  24. ST210TP

    2 Pages

    En
  25. NV06/06L

    2 Pages

    En
  26. SRA166/210-01A

    2 Pages

    En
  27. SC400LC

    2 Pages

    En
  28. SJ80C-18D/24D

    2 Pages

    En
  29. FD Controller

    2 Pages

    En
  30. Jack-knife Arm

    2 Pages

    En
  31. FLEXhand

    2 Pages

    En
  32. SC500

    2 Pages

    En
  33. SC700

    2 Pages

    En
  34. MC35/50/70

    2 Pages

    En
  35. MR35/50

    2 Pages

    En
  36. MC20/10L

    2 Pages

    En
  37. MR35/50

    2 Pages

    En
  38. ST133F/166F/210F

    2 Pages

    En
  39. ST70L/100

    2 Pages

    En
  40. ST210TP

    2 Pages

    En
  41. SRA166/210

    2 Pages

    En