Vacuum Degreasing Equipment Clean Master - 6 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

Catalogue excerpts

Vacuum Degreasing Equipment Vacuum Degreasing Equipment Clean Master

 Open the catalogue to page 1

Clean Master : can manufacture pit type equiptnefiESSiB custom designed effective dimensions am

 Open the catalogue to page 2

Straight-through type This model is equipped with two doors, (front door and rear door) Perfect for lines that run work pieces on conveyors between It can also be used in an in-and-out configuration. (Option) •Claw type transfer -♦Claw type transfeFF= chain conveyor •Claw type transfer + chain conveyor + hoist small trays at the sarrie^ propelled carts used for heat treatment lines orine-based addi before heat treatment, can equipment. This device= each washing cycle.

 Open the catalogue to page 3

Clean Master Swift Clean Master Swift is a short cycling straight through type system Straight through type /20 minute cycle Perfect for short cycling continuous operations. ective dimensions aximum capac Supply pressure 0.1 to 0.15 MPaG, 32C or lower Supply pressure 0.4 to 0.5 MPaG (maximum instantaneous flow is 80 NmVh) Supply pressure 0.4 to 0.5 MPaG (maximum instantaneous flow is 0.2 NmVh) Note 1: Electric power consumption noted above is for electrically heated thermal oil. Note 2: Washing time may vary depending on the shape of the work piece. Note 3: Height of effective dimensions may vary...

 Open the catalogue to page 4

The Ultimate in Washing Before and After Heat Treatment Important issues involved in washing for heat treatment... Single charge solvent consumption of 0.2 liters on average, total running costs are less than 1/3 of trichloroethylene. Decrease solvent control work Specialized distiller and washing chamber that boast 200 L/H distilling performance to prevent solvent from getting dirty and maintain cleaning quality during continuous operations. Solvent does not need Taking care of environmental problems Compliance with air pollution prevention laws, soil pollution control laws and PRTR regulations. Nachi-Fujikoshi's...

 Open the catalogue to page 5

Clean Master Exterior dimensions heat source Side view Heat source: Electric heater model Dimensions for gas boiler models provided upon request. Straight through type Heat source: Electric heater model Dimensions for gas boiler models provided upon request. Side view heat source Tokyo Head Office: Shiodome Sumitomo Bldg. 17F, 1 -9-2 Higashi-shinbashi, Minato-ku, Tokyo 105-0021, Japan Toyama Head Office: 1-1-1 Fujikoshi-Honmachi, Toyama 930-8511, Japan Clean Thermo - Tech Div. Tel Eastern Japan Main Branch Tel •For engineering questions contact Clean & Thermo-Tech Div. at 176-12 Ogake, Namerikawa-shi,...

 Open the catalogue to page 6

All NACHI America catalogues and technical brochures

  1. GSX MILL SLOT

    2 Pages

    En
  2. GSX MILL Series

    16 Pages

    En
  3. GSX MILL VL Hard

    2 Pages

    En
  4. GSX MILL VL Series

    20 Pages

    En
  5. SG Drill Series

    12 Pages

    En
  6. SG Flat Drill

    4 Pages

    En
  7. MC350

    2 Pages

    En
  8. WAVY MILL NWEX

    8 Pages

    En
  9. DURO-SP/V5/V2

    4 Pages

    En
  10. DURO-V5

    2 Pages

    En
  11. Micron Hard

    4 Pages

    En
  12. Pre-Harden

    8 Pages

    En
  13. MACHINE TOOLS

    28 Pages

    En
  14. AG-mill Series

    20 Pages

    En
  15. GS MILL Series

    44 Pages

    En
  16. AQUA Drill Series

    44 Pages

    En