video corpo

Thermal Process Technology II - 36 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

Catalogue excerpts

MORE THAN HEAT 30-3000°C Thermal Process Technology II Annealing, Hardening, Brazing, Forging, Nitriding Hardening Systems Quenching Baths Charging Plates Charging Baskets Other Accessories

 Open the catalogue to page 1

Made in Germany Nabertherm with 350 employees worldwide have been developing and producing industrial furnaces for many different applications for over 60 years. As a manufacturer, Nabertherm offers the widest and deepest range of furnaces worldwide. 150,000 satisfied customers in more than 100 countries offer proof of our commitment to excellent design, quality and cost efficiency. Short delivery times are ensured due to our complete inhouse production and our wide variety of standard furnaces. Setting Standards in Quality and Reliability Nabertherm does not only offer the widest range of standard...

 Open the catalogue to page 2

Overview of Heat Treatment Processes Quenching and Tempering Case Hardening Hardening Tempering Solution Annealing Aging Annealing Recovery Annealing Recrystallization Annealing Stress Relief Annealing Soft Annealing Normalizing Thermal Chemical Diffusion Without Subsequent Hardening: Oxidizing Powder Nitriding Powder Boriding with Subsequent Hardening: Carburizing As a manufacturer of electrically and gas heated furnaces for heat treatment, Nabertherm offers a wide range of accessory equipment and consumable materials required for heat treatment. The MHS 17 hardening system shown on page 17,...

 Open the catalogue to page 4

Chamber Furnaces with Radiation Heating N 7/H - N 1491 These universal chamber furnaces with radiation heating are designed for highly adverse conditions during heat treatment. They are ideally suited for tooling construction processes and in the hardening shop, such as annealing, hardening or preheating for forging. The use of various accessories allow these furnaces to be modified for your application. Standard Features, Table-Top Models N 7/H - N 17/HR Compact, low-cost construction Heating from floor and both side walls Heating elements on support tubes ensure free heat radiation and a long...

 Open the catalogue to page 5

Charging Plates for Models N 7 - N 641/13 We recommend this useful accessory equipment for applications up to 1100 °C to protect the furnace floor. Tmax 1100 °C Three raised edges Hole for draw hook (see page 22 for draw hook) Made of heat-resistant alloy 314 (AISI)/(DIN material no. 1.4841) Material thickness 4 mm Larger plates and custom dimensions available upon request Charging plate Hardening Boxes for Models N 7 - N 161/13 Working with Hardening Boxes Hardening boxes are made of heat-resistant alloy 314 (AISI)/(DIN material no. 1.4841) and also feature a lid for top charging. A ceramic fiber...

 Open the catalogue to page 6

Neutral Annealing Coal MORE THAN HEAT 30-3000°C For protection of tool steel against oxidation and decarburizing, binds oxygen at all process temperatures Workpieces are placed in a hardening box with annealing coal Reusable multiple times with addition of approx. 20 % new granulate

 Open the catalogue to page 7

Stainless Steel Heat Treating Foil to avoid Surface Reactions Single parts requiring protection against decarburizing can be wrapped in a stainless steel heat treating foil off the roll or packed in prepared envelopes or bags. The rolls are available in various lengths and widths, the envelopes and bags are supplied in various dimensions. Foil off the roll can be cut to size using gold plates scissors and the workpiece can be wrapped to requirements. See page 9 for more details about accessory supplies required, such as tongs and special gloves. The protected workpiece can now be loaded into the...

 Open the catalogue to page 8

Annealing Envelopes Annealing envelopes useful up to Tmax 1200 °C For hardening small parts Airtight lock by means of folds of a fold lock or suitable tools (page 8) Rapid heating of the foil binds the oxygen in the annealing envelope preventing virtually all oxidation and decarburizing Rapid quenching in air, oil or water, ensuring high dimensional accuracy Workpieces are placed as tightly as possible in the annealing envelope Envelopes made of ultra-thin stainless steel heat treating foil, welded on three sides, for single use Article no. Annealing envelopes Annealing Bags Annealing bags Annealing...

 Open the catalogue to page 9

Protective Gas Annealing Bag and Holder for Models N 7 - N 61/H Protective gas annealing bag in operation Working with the Protective Gas Annealing Bag and Holder When workpieces made of air-hardened steel must be heat treated under protective gas and quenched, the protective gas annealing bag with holder is an optimal solution. This system consists of a holder with charge carrier and protective gas tube as well as a bag made of stainless steel heat treating foil. We would be pleased to carry out trials at our technical center. The charge is placed on the charge carrier and covered with the protective...

 Open the catalogue to page 10

Protective Gas Boxes for Models N 7 - N 641 Working with Protective Gas Boxes for a Protective Gas Atmosphere The hardening boxes for heat treatment under protective gas are equipped with a protective gas intlet and outlet. A box with protective gas is advisable for larger workpieces requiring defined heat treating. We would be pleased to carry out trials at our technical center. Up to furnace model N 61/H with downward door opening the gas ductway is laid through the upper section of the door collar, for larger furnaces with upward door opening the supply line is laid through the lower furnace...

 Open the catalogue to page 11

Protective Gas Boxes with additional Vacuum Lid for Models N 7 - N 161 Working with Protective Gas Boxes with additional Vacuum Lid to ensure Protective Gas Atmosphere When heat treating bulk goods and hollow parts under defined protective gas atmosphere we recommend the usage of protective gas boxes with an additional vacuum lid. Thus the traces of oxygen in the box can be reduced by a considerable amount which improves the quality of the components accordingly. Protective gas box for N 41/H furnace with additional vacuum lid These boxes are equipped with a lid for top charging, protective gas...

 Open the catalogue to page 12

Vacuum Pump Oil sealed rotary vane vacuum pump for universal use within the low vacuum range. Highly compact and low noise construction. Vacuum pressure gauge included in delivery. Sliding vane rotary pump Sogevac SV 16BG with sucking capacity of max. 16 m³/h 0,5 mbar absolute Connection hose made of stainless steel 1000 mm Connector KF16 Manometer (-1/0,6 bar) Article no. Connections on suction side W D H 601403057 215 281 199 3/4" 1/2" inner thread *Article no. for other possible supply voltages on request Vacuum pump Nominal suction power m3 h 16 Protective Gas Boxes with Hinged Lids for Bulk...

 Open the catalogue to page 13

All Nabertherm catalogues and technical brochures

  1. Laboratory

    64 Pages

    En
  2. Foundry

    64 Pages

    En
  3. Advanced Materials

    72 Pages

    En
  4. Arts & Crafts

    28 Pages

    En
  5. Glass

    44 Pages

    En

Archived catalogues