Catalogue - device server - Moxa Europe

See other catalogues for Moxa Europe

PROFIBUS, PROFIBUS gateway, Power over Ethernet, Ethernet switch, USB converter

Text version of the page

Reset Button—Press the Reset button continuously for 5 sec to load factory defaults: Use a pointed object, such as a straightened paper clip or toothpick, to press the reset button. This will cause the Ready LED to blink on and off. The factory defaults will be loaded once the Ready LED stops blinking (after about 5 seconds). At this point, you should release the reset button.

LED Indicators—NPort 5400's top panel contains six LED indicators, as described in the following table.

NPort 5410/5450/54501

Power in

pui—J

NPort 5400 Series Quick Installation Guide

Fourth Edition, January 2007

1. Overview

Welcome to Moxa NPort 5400, a 4 port communication device that allows you to control RS-232 (for NPort 5410), RS-422/485 (for NPort 5430/54301) or RS-232/422/485 (for NPort 5450/54501) serial devices over a TCP/IP based Ethernet.

NPort 5400 Series is a MOXA Green Product. Moxa's Green Products satisfy the RoHS directive of the European Parliament, and accordingly, do not contain cadmium and cadmium compounds, hexavalent chromium compounds, lead and lead compounds, mercury and mercury compounds, PBBs (polybrominated biphenyls), or PBDEs (polybrominated diphenyl ethers).

2. Package Checklist

Before installing NPort 5400, verify that the package contains the following items:

• 1 NPort 5400 4-Port Serial Device Server

• NPort Document & Software CD

• NPort 5400 Series Quick Installation Guide

• Product Warranty Optional Accessories

DK-35A For 35 mm DIN-Rail; includes 4 screws

Notify your sales representative if any of the above items is missing or

damaged.

3. Hardware Introduction

As shown in the following figures, NPort 5410 has 4 Male DB9 ports, for the RS-232 interface, NPort 5430/54301 has 4 5-pin terminal blocks, for the RS-422/485 interface, and NPort 5450/54501 has 4 Male DB9 ports, for the RS-232/422/485 interface.

RJ45 10/100 Mbps Ethernet port—¹

Terminal Block power input -


LED Name	LED Color	LED Function
Ready	red	Steady on: Power is on and NPort is booting up. Blinking: Indicates an IP conflict, or DHCP or BOOTP server did not respond properly.
	green	Steady on: Power is on and NPort is functioning normally. Blinking: The NPort has been located by NPort Administrator's Location function.
	off	Power is off, or power error condition exists.
Link	orange	10 Mbps Ethernet connection.
	green	100 Mbps Ethernet connection.
	off	Ethernet cable is disconnected, or has a short.
P1, P2, P3, P4	orange	Serial port is receiving data.
	green	Serial port is transmitting data.
	off	No data is being transmitted or received through the serial port.

~Q1 |U U| |U U| |U U| |D~

ndicator LEDs —' Input buttons LCM display panel Male DB9 serial port

4vÄ> «£v7> «£v> 4v7>

NPort 5430/54301

Power input

LCM Display Panel—When the NPort 5400 unit is powered up, you will a see a display similar to:


N	P	5	4	1	0		6	1	4	0	5
1	9	2		1	6	8		1	2	7		2	5	4

RJ45 10/100 Mbps Ethernet port—¹

Terminal Block power input -

This is where NP5410 61405 is the server's name, and 192.168.127.254 is the server's IP address.

LCM Panel Operation—There are four buttons on NPort 5400's top panel used to operate the server's LCM panel. Going from left to right, the buttons are:


	Button	Action
	MENU	Activates the main menu, or returns to a lower level.
	A	Scrolls up through a list of items shown on the LCM panel's second line.
		Scrolls down through a list of items shown on the LCM panel's second line.
	SEL	Selects the option listed on the LCM panel's second line.

ndicator LEDs—¹ Input buttons LCM display panel RS-422/485 Terminal Block-

Detailed LCM Panel Operating instructions can be found on the CD-ROM in the "NPort 5400 Series User's Manual."

P/N:1802054000300

— l —

— 2 —

— 3 —

device server - Moxa Europe - #1

PROFIBUS, PROFIBUS gateway, Power over Ethernet, Ethernet switch, USB converter