Text version of the page

4. Hardware Installation Procedure

Pull High/low Resistors for the RS-485 Port 1 2 3

8. Terminal Block Wiring Ϋ Ϋ NPort 5430/5430I

STEP 1 : After removing NPort 5400 from the box, the first thing you should do is attach the power adaptor. SW Pull High Pull Low Terminator ON 1K 1K 1K STEP 2 : Connect NPort 5400 to a network. Use a standard straight-through Ethernet cable to connect to a Hub or Switch. When setting up or testing NPort 5400, you might find it convenient to connect directly to your computer’s Ethernet port. In this case, use a cross-over Ethernet cable. Default OFF 150K 150K ---

6. Software Installation Information

STEP 3 : Connect NPort 5400’s serial port to a serial device. To install NPort Administration Suite , insert the NPort Document & Software CD STEP 4: Placement Options into your computer’s CD-ROM drive. Once the NPort Installation CD Wall or Cabinet Mounting window opens, click on the Installation button, and then follow the instructions on the screen. To view detailed information about NPort Administration Suite , click on the

9. Environmental Specifications

The NPort 5400 comes with two metal attachment plates for attaching the embedded computer to a wall or the inside of a cabinet. First, use two screws per bracket to attach the brackets to the rear of the 5400. Next, use two screws per bracket to attach the 5400 to a wall or cabinet. The heads of the screws should be less than 6.0 mm in diameter, and the shafts should be less than 3.5 mm in diameter, as shown by the figure at the right. Documents button, and then select “NPort 5400 Series User’s Manual” to open the pdf version of this user’s guide. Power requirements NPort 5410 NPort 5430 NPort 5430I NPort 5450 NPort 5450I 12 to 48 VDC, 350 mA at 12V (max.) 12 to 48 VDC, 360 mA at 12V (max.) 12 to 48 VDC, 585 mA at 12V (max) 350 mA at 12V (max) 554 mA at 12V (max) (must use Class 2 or LPS power supply) Operating temp. 0 to 55C (32 to 131F) Operating humidity 5 to 95% RH Dimensions (W×D×H)158 × 33 × 103 mm 6.22 × 1.3 × 4.06 inch Surge protection 15 KV ESD for serial port Magnetic isolation 1.5 KV for Ethernet Power line protection 4 KV Burst (EFT), EN61000-4-4 2 KV Surge, EN61000-4-5 Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

7. Pin Assignments and Cable Wiring

6.0 mm3.5 mm DB9 Male Port Pinouts Pin assignments apply to NPort 5410 (RS-232 only), 5450, and 5450I. DB9 Male Pin RS-232 RS-422/ 2-wire 4-wire RS-485 RS-485 DIN-Rail Mounting 1 DCD TxD-(A) --- DIN-rail attachments can be purchased separately to attach the product to a DIN-rail. When snapping the attachments to the DIN-rail, make sure that the stiff metal springs are at the top. 2 RxD TxD+(B) ---

1569

3 TxD RxD+(B) Data+(B) ATTENTION 4 DTR RxD-(A) Data-(A) 5 GND GND GND Wall Mount DIN-Rail 6 DSR --- --- 7 RTS --- --- 8 CTS --- --- 9 --- --- --- RS-232 Wiring DB9 Female to DB9 Male DB9 Female to DB25 Male There is a risk of explosion if the real-time clock battery is replaced with the incorrect battery type!

5. Pull High/low Resistors Setting for the RS-485 Port

DIP switches on the bottom of NPort 5400 are used to set the pull high/low resistor values for each serial port. Copyright 2007 Moxa Technologies Co., Ltd. All rights reserved. Reproduction without permission is prohibited. Tel: +886-2-8919-1230
0 H www.moxa.com Fax: +886-2-8919-1231
1 H support@moxa.com

— 4 — — 5 — — 6 —