TRAC-DATA CONNECTORS
44Pages

TRAC - DATA CONNECTORS

TRAC D-SUB Data signal connectors D-SUB connectors, designated TRAC, were special- ly developed for use in supervisory control systems. TRAC connectors are fitted with sturdy cast-zinc covers for 360° EMI screening and can be coded When ordering connector sets, it is required to separately order the contacts (single or strip) and shielding sleeve (different sizes). Basically, there are two types of contact housing: The connectors comply with protection class IP44 D-SUB connectors from the TRAC series can be or- dered either as single parts or as sets. TRAC socket/pin housing, the standard...

TRAC D-SUB Data signal connectors Mechanical properties connectors Strain relief The cable clamp shall be tightly pressed into the guiding grooves Elevated spikes at the corners ensure a proper contact with the connector cover- strain relief compression The cable is held in the cable clamp with strain relief compression onto the cabel. The cable clamps have different diameters for use with various cables. Cable diameters can be adapted to the cable clamp size using heat-shrinkable tubes. In such cases and when cable types are used the first time, the strain relief crimp should be tested by...

CD $£H=£ TRAC D-SUB Data signal connectors 3.2 Single parts and contacts for data signal connectors D-SUB 3.2.7 Socket housings D-SUB TRAC

CD $£H=£ TRAC D-SUB Data signal connectors 3.2.2 Pin housings D-SUB TRAC

TRAC D-SUB Data signal connectors 3.2.3 Socket housings D-SUB TRAC H Material: Thermoplastic /steel tin plated

TRAC D-SUB Data signal connectors Covers D-SUB Material: Zinc cast (self passivating)

TRAC D-SUB Data signal connectors 3.2.6 Cable damps I shielding sleeves I wire hole plugs Cable clamps Material: Brass tin-plated * Supporting sleeve for internal shielding at SUKABC12X

TRAC D-SUB Data signal connectors Wire hole plugs Material: Zinc cast (self passivating) * Reducing fixing plates for smaller D-SUB housing application

TRAC D-SUB Data signal connectors 3.2.8 Screws I spring washers Plug screws (hex, socket screws) Material: Stainless steel

CD $£H=£ TRAC D-SUB Data signal connectors Material: Stainless steel

CD $£H=£ TRAC D-SUB Data signal connectors 3.3 D-SUB Connector sets, TRAC * Layoutcode for special layouts: socket housing chapter 3.2.1 / pin housing chapter 3.2.2 Ordering example D-SUB plug (TRACST), 25-pole/socket housing (S25), cable clamp SUKABC12 (C12), wire hole plug (BL), screw M3 x 34mm (1) = Item number.: TRACSTS25C12BL1 Contacts and Shielding sleeves for crimping EMC braids to cable clamp have to be ordred seperately according individual requirements.. Shielding sleeves: chapter 3.2.6

TRAC D-SUB Data signal connectors Wire hole plug Bolt large Coding plate Fixing plate Layoutcode for special layouts: Item number socket housing chapter 3.2.1 Ordering example: D-SUB receptacle (TRACDO), 25-pole/pin housing (P25), cable clamp SUKABC10S (C10S), cable clamp Contacts and Shielding sleeves for crimping EMC braids to cable clamp have to be ordred seperately according individual requirements. Shielding sleeves: chapter 3.2.6

TRAC D-SUB Data signal connectors 3.3.3 Mounting strip TRACBE for direct fixation to casings/boards Layoutcode for special layouts: socket housing chapter 3.2.1 / pin housing chapter 3.2.2 Ordering example: D-SUB mounting strip (TRACBE), 25-pole/pin housing (P25), Unterlagscheibe 1.5 mm (U1.5) Contacts have to be ordred seperately according individual requirements.

TRAC D-SUB Data signal connectors 3.4 D-SUB Connector sets, TRAC H for increased voltage requirements Wire hole plugs Item number Ordering example D-SUB plug (TRACHST), 25-pole/socket housing (S25), cable clamp SUKABC12 (C12), wire hole plug (BL), screw M3 x 34mm (1) = Item number: TRACHSTS25C12BL1 Contacts and Shielding sleeves for crimping EMC braids to cable clamp have to be ordred seperately according individual requirements. Shielding sleeves: chapter 3.2.6

TRAC D-SUB Data signal connectors Wire hole plug Bolt large Coding plate Fixing plate Item number Ordering example: D-SUB receptacle (TRACHDO), 25-pole/pin housing (P25), cable clamp SUKABC10S (C10S), cable clamp Contacts and Shielding sleeves for crimping EMC braids to cable clamp have to be ordred seperately according individual requirements. Shielding sleeves: chapter 3.2.6

TRAC D-SUB Data signal connectors 3.4.3 Mounting strip TRACHBE for direct fixation to casing/boards Ordering example: D-SUB mounting strip (TRACHBE), 25-pole/pin housing (P25), Unterlagscheibe 1.5 mm (U1.5) Contacts have to be ordred seperately according individual requirements.

TRAC D-SUB Data signal connectors 3.5.1 Plug cover set TRACST Ordering example: D-SUB plug (TRACDO), size 1 (1) = Item number: TRACDOI Other components have to be ordered seperately according individual requirements

RAC D-SUB Data signal connectors Crimpingtool for power contacts size 8

TRAC D-SUB Data signal connectors Cutting pliers for removing coding pins Item number Tool for cutting of the coding pins on the cover (special shape of cutting head) Coding tool Item number Tool for inserting coding slides into coding plate Hex.socket screw driver for fixing screws Item number Tool for tightening the hex. socket screws M3

TRAC D-SUB Data signal connectors 3.7 Assembly instructions D-SUB TRAC / TRAC H Standard Part sets Standard part sets conclude all single parts except shielding sleeves, contacts, shrinkable tubes cable ties. Following parts sets are available in 3 sizes: Connectors TRACST and TRACHST Receptacles TRACDO and TRACHDO Mountig strips TRACBE and TRACHBE Appart from standard TRAC/TRACH contact housings for 9-, 15-, and 25-pole size HD20 contacts (pins/so- ckets) other arangements and combinations with size 8 power contacts are available on request, (see 3.2) Contacts are to be selected according...

TRAC D-SUB Data signal connectors Conductor dismanteling * depending on contact position and used cable entrance of the cover