Catalogues - digital-indicator

Catalogue Digital indicator

www.mitutoyo.com

Page

/ 13

Contact the
Manufacturer

Where to buy
this product ?

Request
a Quote

MITUTOYO - 2685, 39662, 260275, 81573, 17217

/ 13

See other catalogues for MITUTOYO

Text version of the page

ABSOLUTE Digimatic Indicator ID-C

SERIES 543 — with Green/Red LED and GO/NG Signal Output Function

FEATURES

•With the max./min. value holding function, "The Signal ID-C achieves the IP54 the signal ID-C can output the signal of the protection level to resist dust and

(jgT54

(Refer to the page 9 for details.)

contaminants for industrial safe operation in harsh machine shop environments.

G0/±NG judgment result against the peak values set. Substitute for the mechanical/

ABSOLUTE

Absolut« System Patented by MTUTOVO

(Refer to the page 9 for details.)

electrical contact, thejudgment is carried out by calculating the measurement data obtained. This provides high reliability with no deterioration of the contact point and volume adjustment.

• The signal can be output to an external device like a sequencer through the NPN open-collector.

• The G0/±NG judgment result is also indicated by the green/red LED and the "<, 0, >" signs on LCD.

• Employing the ABSOLUTE linear encoder, the Signal ID-C always industrial displays the spindle "Absolute Position" from the origin at power-on. Also unlimited response speed eliminates over-speed errors.

Technical Data

Accuracy: Refer to the list of specifications

(excluding quantizing error) Resolution: 0.001mm, ,0000570.001mm or

.000170.001mm Display: LCD

Length standard: ABSOLUTE electrostatic capacitance type

linear encoder Max. response speed: Unlimited Measuring force: 2.0N or less Stem dia.: 8mm (ISO/JIS type) or 3/8" (ANSI/AGD type) Contact point: Carbide ball with M2.5x0.45 (ISO/JIS type)

Carbide ball with #4-48UNF (ANSI/AGD type) Power supply: DC12- 24V±10% Dust/Water protection level: IP54

Function

Data output (-NG/OK/NG signal, NPN open collector), Remote control (hold-preset, preset-recall, zero-set), Orlgin-set/Preset, Zeroset, GO/±NG judgment, Max/MIn/ Runoutvalue holding, Counting direction switching, Power ON/OFF, inch/mm conversion (inch/mm models) Alarm: Low voltage, Counting value composition error, Over-flow error, Tolerance limit setting error

Optional Accessory

902011: Spindle lifting lever* (ISO/JIS type)

902794: Spindle lifting lever* (ANSI/AGD type)

540774: Spindle lifting cable*

125317: Rubber boot

---: Backs (See page 266.)

---: Contact points (See page 264.)

*When using the spindle lifting lever/cable, IP54 is not guaranteed.

Output pattern

SPECIFICATIONS


				I I ISO/JIS type	I I ANS^AGD type
Resolution	Order No. (w/ lug, flat-back)	Range	Accuracy	Measuring force	Remarks
0.001mm	543-280 I 543-280B	12.7mm	0.003mm	2.0N or less	-

Inch/Metric


Resolution	Order No.(w/lug, flat-back)		Range	Accuracy	Measuring force	Remarks
.0000570.001mm	543-281	543-281B	.5"	.00012"	2.0N orless	—
.0000570.001mm	543-282	543-282B	.5"	.00012"	2.0N orless	—
.000570.01mm	543-283	543-283B	.5"	.00012"	2.0N orless	—


\|Wire	-NG	OK	+ NG	Composition error
Orange (- NG)	Low	High	High	High
Green (OK)	High	Low	High	High
Brown (+ NG)	High	High	Low	High
LED	Red	Green	Red	Red (blinking)
LCD	<	0	>	" x.xxE" indication

DIMENSION

I/O Specifications

Unit: mm

ISO/JIS Type


Wire	Signal	I/O	Description
Black	- V (GND)	—	Connectedtomlnus(-)termlnal
Red	+ V(GND)	I	Power supply (12 - 24VDC)
Orange	- NG	0	Tolerancejudgment result output: Only the terminal corresponding to a judgment result is set to the below level.
Green	OK	0
Brown	+ NG	0
Yellow	PRESET RECALL ZERO	I	External Input terminal: If the relevant terminal Is set to the low I level, Its slgnalbecomes true.
Blue	HOLD_RESET	I
Shield	FG	—	Connected to GND

28.5

10.6


		OUT
	HOoOOpF¹-	11^
	\-^U	^—Ib^

Output circuit

LTl

Load

Outputvoltage: Max. 24V Output current: Max. 30mA Output saturated voltage: Max. 0.3V

Note 1: Dimensions of the inch (ANSI/AGD Type) dial indicator partly differ from those of the metric (ISO/JIS Type) indicator.

Note 2: Inch (ANSI/AGD Type)

dial indicator is provided with a stem of 3/8" dia. and #4-48UNF thread mount for the contact point.

Input circuit

Use a non-voltage output such as an open collector output or relay output.

-G-DC+12-24V

M2.5x0.45

24kQ

OUT

1000pF:± Input current: \— Max. 10mA ^7tT

toyo

237