Catalogs >
Mikron Machining >
CrazyMill Cool

CrazyMill Cool
12Pages

Catalog excerpts

Crazy Mill Cool Cool milling to new horizons Through coolant, carbide Endmills

CrazyMill Cool Revolutionary in the minute detail Integrated coolant channels Cooling channels are integrated into the carbide shaft. Coolant ports are at the end of the shaft taper where they produce a steady and massive cooling effect of the cutting edges which facilitates in turn high cutting speeds. A targeted ushing of the chips is thus also assured and gives best surface quality. Shaft A robust carbide shaft helps to achieve stable and non vibrating milling. Highest precision and surface quality are achieved. Solid carbide A special carbide has been developed for the CrazyMill Cool...

Open the catalog to page 2

CrazyMill Cool Always top performing A small Endmill lives up to highest expectations - cooled. Machining of difficult materials With difficult materials such as stainless and acid resistant steels, titanium chrome-cobalt alloys as well as superalloys, milling tools are exposed to considerable wear. With high temperatures and reduced heat conductivity of the material, the heat transfers usually to the cutting edges, which subsequently reduces much of the tool life expectancy. External cooling is often not enough to control sufficiently the temperature of the tool. The integrated through...

Open the catalog to page 3

CrazyMill Cool Type A Article available from stock

Open the catalog to page 4

Material group Non-alloy steels Alloy steels Stainless steel - ferritic Stainless steel -martensitic 2.1020 Bronze high-strength, Ampco Titanium pure P High alloy steels, tool steels M Stainless steel -austenitic Aluminum alloy wrought Aluminum alloy cast Copper Brass, Bronze < 200 HB Titanium alloys Nickel alloys Cr -Co alloys Material group Non-alloy steels Alloy steels 2.1020 Bronze high-strength, Ampco Titanium pure P High alloy steels, tool steels Stainless steel - ferritic Stainless steel -martensitic M Stainless steel -austenitic Aluminum alloy wrought Aluminum alloy cast Titanium...

Open the catalog to page 5

CrazyMill Cool Type B 3,0 x d D Article available from stock

Open the catalog to page 6

Material group Non-alloy steels Alloy steels Stainless steel - ferritic Stainless steel -martensitic 2.1020 Bronze high-strength, Ampco Titanium pure P High alloy steels, tool steels M Stainless steel -austenitic Aluminum alloy wrought Aluminum alloy cast Copper Brass, Bronze < 200 HB Titanium alloys Nickel alloys *1 Cr -Co alloys *1 WMaterial group Non-alloy steels Alloy steels 2.1020 Bronze high-strength, Ampco Titanium pure P High alloy steels, tool steels Stainless steel - ferritic Stainless steel -martensitic M Stainless steel -austenitic Aluminum alloy wrought Aluminum alloy cast...

Open the catalog to page 7

CrazyMill Cool Type C 5xd D Article available from stock

Open the catalog to page 8

Open the catalog to page 9

CrazyMill Cool Technical information Clamping equipment Cooling lubricant / lter • Hydraulic expansion chuck: For a “smooth” cut with a minimal run out (T.I.R.) and very high surface quality. Direct clamping for shank diameter 4, 6 and 8 mm. Clamping with intermediate sleeve for shank diameter 3 mm. For optimum results Mikron Tool recommends the use of cutting oil as a coolant. Alternatively emulsion can also be used. No specic lter is necessary. Large lubricant channels enable to use standard lter. Pressure and quantity • Shrink-t chucks: Guarantee minimal run out (T.I.R.) with secure...

Open the catalog to page 10

CrazyMill Cool New horizons in machining Application example Material: 904L; X1NiCrMoCu 25-20-5; 1.4539 Tool: CrazyMill Cool Type B; diameter 3 mm High efciency milling of a slot (1), a pocket (2) and a rib (3). Machine building Conveyor Technique Food industry Chip removal rate Q [cm /min] Through coolant Endmill Cutting edges with protection phase of 45°. Ideal for stainless steel, titanium and nickel based steels. Machining of non ferrous materials and all carbon steels in general is also possible. Possible machining direction Cutting edges with a corner radius For perfect surface...

Open the catalog to page 11

Your contacts Headquarter and Production: Mikron Tool SA Agno PO Box 340 6934 Bioggio Switzerland Phone +41 91 610 40 00 Fax +41 91 610 40 10 mto@mikron.com Production for Germany and Regrinding for EU: Mikron GmbH Rottweil Abteilung Werkzeuge Berner Feld 71 78628 Rottweil Germany Phone +49 741 5380 450 Fax +49 741 5380 480 info.mtr@mikron.com North and South America Sales Mikron Corp. Monroe P.O. Box 268 200 Main Street Monroe, CT 06468 USA Phone +1 203 261 3100 Fax +1 203 268 4752 mmo@mikron.com www.youtube.com/mikrongroup www.mikron.com/tool Information and technical data are liable to...

Open the catalog to page 12