Catalogs >
Micro Sensor Co.,Ltd >
MPM289 Piezoresistive OEM Pressure Sensor

MPM289 Piezoresistive OEM Pressure Sensor
4Pages

Catalog excerpts

MPM289 Piezoresistive OEM Pressure Sensor - 1

Features • Pressure range 0~ 35kPa...100MPa • Gauge, absolute, sealed gauge • Constant current power supply • Isolated construction, enable to measure various media • 019mm standard OEM pressure sensor • Full stainless steel 316L • Wide temperature compensation -10°C~ 70C Application • Industrial process control • Level measurement • Gas, liquid pressure measurement • Pressure checking meter • Pressure calibrator • Liquid pressure system and switch • Cooling equipment and air conditioning system • Aviation and navigation inspection Introduction MPM289 OEM sensor is the piezoresistive pressure sensor with isolated construction and precise compensation. It uses high stable silicon die. Stainless steel 316L housing with diameter 019mm. Wider temperature compensation and zero correction are calibrated by laser trimming technics. The measured pressure is transmitted onto silicon die through 316L diaphragm and inner media, to transform the pressure to electric signal. MPM289 pressure sensor is inspected and screened on automatic production line, testing and checking time after time strictly. It is widely used for various pressure measurement fields. Electric Specification Power supply: <2.0mADC Electric connection: Kovar pin Common mode voltage output: 50% input (typ.) Input impedance: 2kQ~ 4kQ Output impedance: 4kQ~ 6kQ Response (10%~ 90%): <1ms Insulation resistor: 100MQ, 100VDC Overpressure: 1.5 times FS MICRO SENSOR CO.,LTD Construction Diaphragm: stainless steel 316L http://www.microsensor.cn Add: No.18,Yingda Road Baoji,P.R.China, 721006

Open the catalog to page 1

MPM289 Piezoresistive OEM Pressure Sensor - 2

MPM289 Pressure Sensor (V1.0) Housing: stainless steel 316L Pin: Kovar O-ring: Viton Net weight: ~25g Environment Condition Position: deviate 90° from any direction, zero change s±0.05%FS Shock: no change at 10gRMS, (20~ 2000) Hz Impact: 100g, 11ms Media compatibility: the gas or liquid which is compatible with stainless steel and viton Basic Condition Media temperature: (30±1)°C Environment temperature: (30±1)C Shock: 0.1g (1m/s2)Max Humidity: (50%±10%)RH Local air pressure: (86~ 106)kPa Power supply: (1.5±0.0015)mADC Basic Specification MICRO SENSOR CO.,LTD -2-

Open the catalog to page 2

MPM289 Piezoresistive OEM Pressure Sensor - 3

MPM289 Pressure Sensor (V1.0) **Code 35K0 Max. Linearity:±0.25(%FS,BFSL) Gauge Only <3.5MPa >7MPaThe suggested installation dimension is 019^ mmElectric Connection Pin Order Guide MPM289 Piezoresistive OEM Pressure Sensor Range code Pressure range Ref.

Open the catalog to page 3

MPM289 Piezoresistive OEM Pressure Sensor - 4

O O-ring Code Compensation L Laser trimming Code Electric connection 1 Kovar pin(default) 2* 100mm silicon rubber flexible wires 1. It is recommended that the sensor should be installed as Suspended Mode to avoid face tight press and avoid affecting sensor stability. 2. Please pay attention to protect the diaphragm and the compensated board to prevent any damage or bad performance. 3. Temperature resistant range of standard Viton O-ring of sensor is -20°C ~ 2500. When working temperature is lower than -20C, or sensor is applied in critical environment, please contact us. MICRO SENSOR...

Open the catalog to page 4