Catalogue - Safety Brakes | Business Field Documentation - MAYR - (Version JPG)

See other catalogues for MAYR

Hysteresis clutch, DC gearmotor, Brake, Worm gear motor, Gear-motor

Text version of the page

mayr

Half-wave Rectifiers and Bridge Rectifiers Type 02_.000.6

Application

Ì189728 V V

Rectifiers are used to connect DC units to alternating voltage supplies, for example electromagnetic brakes and clutches (ROBA-stop®, ROBA-quick®, ROBATIC®), electromagnets, electrovalves, contactors, switch-on safe DC motors, etc.

Function

The AC input voltage (VAC) is rectified (VDC) in order to operate DC voltage units. Also, voltage peaks, which occur when switching off inductive loads and which may cause damage to insulation and contacts, are limited and the contact load reduced.

Electrical Connection (Terminals)

1 + 2 Input voltage

3 + 4 Connection for an external switch for DC-side switching

5 + 6 Coil

7 - 10 Free nc terminals (only for size 2)

s (mm)

Order Number

__ / 0 2 A

Size 1

up to 4

.0 0 0.6


Size	A	B	C	0D	E
1	34	30	25	3,5	4,5
2	54	30	44	4,5	5,0
3/4	64	30	54	4,5	5,0

4 5

Half-wave rectifier Bridge rectifier

Accessories: Mounting bracket set for 35 mm rail acc. to EN 50022: Article-No. 1803201


Technical Data	Bridge rectifier			Half-wave rectifier
Calculation output voltage	VDC = VAC x 0,9			VDC = VAC x 0,45
Type	1/025	2/025	1/024	2/024	3/024	4/024
Max. input voltage	230 VAC	230 VAC	400 VAC	400 VAC	500 VAC	600 VAC
Max. output voltage	207 VDC	207 VDC	180VDC	180VDC	225 VDC	270 VDC
Output current at < 50°C	2,5 A	2,5 A	3,0 A	4,0 A	4,0 A	4,0 A
Output current at max. 85 °C	1,7 A	1,7 A	1,8 A	2,4 A	2,4 A	2,4 A
Max. coil capacity at 115 VAC < 50 °C	260 W	260 W	-	-	-	-
Max. coil capacity at 115 VAC up to 85 °C	177 W	177 W	-	-	-	-
Max. coil capacity at 230 VAC < 50 °C	517 W	517 W	312 W	416 W	416 W	416 W
Max. coil capacity at 230 VAC up to 85 °C	352 W	352 W	187 W	250 W	250 W	250 W
Max. coil capacity at 400 VAC < 50 °C	-	-	540 W	720 W	720 W	720 W
Max. coil capacity at 400 VAC up to 85 °C	-	-	324 W	432 W	432 W	432 W
Max. coil capacity at 500 VAC < 50 °C	-	-	-	-	900 W	900 W
Max. coil capacity at 500 VAC up to 85 °C	-	-	-	-	540 W	540 W
Max. coil capacity at 600 VAC < 50 °C	-	-	-	-	-	1080 W
Max. coil capacity at 600 VAC up to 85 °C	-	-	-	-	-	648 W
Peak reverse voltage	1600 V	1600 V	2000 V	1600 V	2000 V	2000 V
Rated insulation voltage	250 Vrms	320 Vrms	500 Vrms	500 Vrms	630 Vrms	630 Vrms
Pollution degree (insulation coordination)	2	2	2	1	2	2
Protection fuse		To be included in the input voltage line.
Recommended microfuse switching capacity H The microfuse corresponds to the max. possible connection capacity. If fuses are used corresponding to the actual capacities, the permitted limit integral R must be observed on selection.	FF 3,15A	FF 3,15A	rr 4A	nn 5A	FF 5A	FF 5A
Permitted limit integral l²t	40 A²s	40 A²s	50 A²s	100 A²s	50 A²s	50 A²s
Protection		IP65 components, encapsulated / IP20 terminals
Terminals		Cross-section 0,14 -		1,5 mm² (AWG 26-14)
Ambient temperature			- 25 °C up to + 85 °C
Storage temperature			- 25 °C up to + 105 °C
Conformity markings	UL, CE	UL, CE	UL, CE	UL, CE	UL, CE	CE
Installation conditions	The installation position can be user-defined. Please ensure sufficient heat dissipation and air convection! Do not install near to sources of intense heat!

Safety Brakes | Business Field Documentation - MAYR - #19

Hysteresis clutch, DC gearmotor, Brake, Worm gear motor, Gear-motor