Hydraulic Motors MLHS MLHT MLHV - 55 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

  13. P. 40

  14. P. 50

Catalogue excerpts

DISC VALVE HYDRAULIC MOTORS CONTENTS Page “M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material. “M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.

 Open the catalogue to page 2

DISC VALVE HYDRAULIC MOTORS GENERAL INFORMATION: Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs on tapered roller bearings and can absorb high axial...

 Open the catalogue to page 3

HYDRAULIC MOTORS MLHS APPLICATION » » » » » » » Conveyors Metal working machines Agricultural machines Road building machines Mining machinery Food industries Special vehicles etc. » Model - Disc valve, roll-gerotor » Flange and wheel mount » Short motor » Motor with Drum Brake » Tacho connection » Speed sensoring » Side and rear ports » Shafts- straight, splined and tapered » SAE, Metric and BSPP ports » Other special features Pressure fluid Pa=1125 [500] Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) Temperature range, Optimal Viscosity range, SUS [mm /s] 2 Pressure Losses Oil flow in Pressure...

 Open the catalogue to page 4

MLHS MOTORS SPECIFICATION DATA Displacement, in³/rev [cm³/rev] lb-in [daNm] with Drain Line Max. Starting Pressure with Unloaded Shaft, PSI [bar] at max. press. drop cont. lb-in [daNm] Min. Speed***, [RPM] Weight, lb [kg] For Rear Ports + .88[0,40] * Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure drop must not occur simultaneously. 2. Recommended filtration is...

 Open the catalogue to page 5

MLHS MOTORS SPECIFICATION DATA (continued) Displacement, in³/rev [cm³/rev] lb-in [daNm] with Drain Line Max. Starting Pressure with Unloaded Shaft, PSI [bar] Min. Starting Torque at max. press. drop cont. 4960 [56] lb-in [daNm] * Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure drop must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness...

 Open the catalogue to page 6

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. 7

 Open the catalogue to page 7

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. 8

 Open the catalogue to page 8

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. 9

 Open the catalogue to page 9

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. 10

 Open the catalogue to page 10

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. 11

 Open the catalogue to page 11

MLHS MOTORS FUNCTION DIAGRAMS The function diagrams data is for average performance of randomly selected motors at back pressure o 5÷10 bar [72.5÷145 PSI] and oil with viscosity of 32 mm²/s [150 SUS] at 50°C [122 F]. MAX. PERMISSIBLE SHAFT SEAL PRESSURE Max. return pressure without drain line or max. pressure in the drain line - continuous operations - intermittent operations

 Open the catalogue to page 12

MLHS MOTORS DIMENSIONS AND MOUNTING DATA MLHS, MLHSF, MLHSA M Shaft T Shaft SW Shaft D Shaft M Shaft T Shaft SW Shaft D Shaft Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW * -For Rear Ported Motors. 13 Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

 Open the catalogue to page 13

MLHS MOTORS DIMENSIONS AND MOUNTING DATA MLHSW M Shaft T Shaft SW Shaft D Shaft C Shaft G Shaft S Shaft Rear ports Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW * -For Rear Ported Motors. 14

 Open the catalogue to page 14

MLHS MOTORS F Magneto Mount (4 Holes)

 Open the catalogue to page 15

MLHS MOTORS Versions Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW MOTORS WITH TACHO CONNECTION max L

 Open the catalogue to page 16

MLHS MOTORS DIMENSIONS AND MOUNTING DATA - MLHSBD (MOTOR WITH DRUM BRAKE) Actuating the brake level, the brake shaft is turned. The rectangular shape of the inner part of this shaft forces the brake pads to be pressed against the brake drum. This brakes the wheel or the winch drum. Releasing the level, the springs pull it and the brake pads back to the initial position. The motor output A B shaft is released. Minimum angle adjustment is 10º. It can be adjusted by dismantling the level. Depending on the application You can choose the actuating direction of the brake level. The rod connection actuating...

 Open the catalogue to page 17

MLHS MOTORS SHAFT EXTENSIONS 1¼'' [31,75] straight, Parallel key 5 16 ''x 5 16 ''x 1 ¼'' BS46 Max. Torque 6815 in-lb [77 daNm] 1'' [25,4] straight, Parallel key ¼''x ¼''x 1'' BS46 Max. Torque 3900 in-lb [44 daNm] 14T Splined, 1¼'' [31,75], ANS B92.1-1976 Max. Torque 6815 in-lb [77 daNm] ø32 straight, Parallel key A10x8x45 DIN 6885 Max. Torque 6815 in-lb [77 daNm] Teeth 14 pressure angle 30° 1'' [25,4], SAE 6B Splined BS2059 Max. Torque 3900 in-lb [44 daNm] 1'' [25,4], SAE 6B Splined BS2059 Max. Torque 3400 in-lb [38 daNm] 7/8''-13T splined DP16/32 ANS B92.1-1970 Max. Torque 1770 lb-in [20 daNm] ø34,85,...

 Open the catalogue to page 18

All M+S Hydraulic PLC catalogues and technical brochures

  1. E5-STEERINGUNIT

    54 Pages

    En
  2. E4-ACCESSORIES

    67 Pages

    En
  3. E3-HEAVY DUTY

    53 Pages

    En
  4. E2-DISKVALVE

    56 Pages

    En
  5. E1-SPOOLVALVE

    123 Pages

    En