HEAVY DUTY HYDRAULIC MOTORS
53Pages

HEAVY DUTYiM

HEAVY DUTY HYDRAULIC MOTORS CONTENTS Page “M+S HYDRAULIC” can accept no responsibility for possible errors in catalogues, brochures and other printed material. “M+S HYDRAULIC” reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed.

DISC VALVE HYDRAULIC MOTORS GENERAL INFORMATION: Orbit motors convert hydraulic energy (pressure, oil flow) into mechanical energy (torque, speed). Hydraulic orbit motors operate on the principle of an internal gear (rotor) rotating within a fixed external gear (stator). The internal gear transmits the torque generated by the application of pressure from hydraulic oil fed into motor which is then delivered via the motor's output shaft. Orbit motors have high starting torque and constant output torque at wide speed range. The output shaft runs on tapered roller bearings and can absorb high...

HYDRAULIC MOTORS MLHSEM APPLICATION » » » » » » » » Sawmill machines Woodworking machines Metal working machines Agricultural machines Road building machines Mining machinery Food industries Special vehicles etc. » Model - Disc valve, roll-gerotor » Wheel mount » Side ports » Shaft - tapered » SAE and Metric ports » Other special features Max. Pressure Drop, Max. Oil Flow, Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) Temperature range, Optimal Viscosity range, SUS [mm /s] ISO code 20/16 (Min. recommended fluid filtration of 25 microns) Oil flow in Pressure drop Viscosity drain line PSI...

EPMS MLHSEM MOTORS MOTORS SPECIFICATION DATA lb-in [daNm] with Drain Line Max. Starting Pressure with Unloaded Shaft, PSI [bar] Min. Starting Torque lb-in [daNm] Min. Speed***, [RPM] * Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code 20/16. A nominal f iltration of 25 micron...

EPMS MLHSEM MOTORS MOTORS DIMENSIONS AND MOUNTING DATA MLHSEM 400 8.35 [212,0] 6.73 [171,0] 2.73 [69,4] Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW PERMISSIBLE SHAFT LOADS The output shaft runs in tapered bearings that permit high axial and radial forces. Curve shows max. radial shaft load at bearing life of 2000 hours at 100 RPM. Pr daN

EPMS MLHSEM MOTORS MOTORS Pos.3 - Port Size/Type [standard manifold to each] 2 4 - side ports, 2xG1/2, G1/4, BSP thread, ISO 228 - side ports, 2x7/8-14 UNF, O-ring, 7/16-20 UNF Pos.4 - Special Features [see page 48] Pos.5 - Design Series omit - Factory specified The hydraulic motors are mangano phosphatized as standard.

HYDRAULIC MOTORS MTK APPLICATION » Conveyors » Metal working machines » Agricultural machines » Road building machines » Mining machinery » Food industries » Special vehicles » Plastic and rubber machinery etc. » Model - Disc valve, roll-gerotor » Flange mount with wheel mount » Side and rear ports » Shafts - straight, splined and tapered » Metric, SAE and BSPP ports » Other special features lb-in [daNm] Permissible Shaft Loads, Pa=2250 [1000] Mineral based- HLP(DIN 51524) or HM(ISO 6743/4) Temperature range, Optimal Viscosity range, SUS [mm /s] ISO code 20/16 (Min. recommended fluid...

MTK EPMS MOTORS MOTORS lb-in [daNm] Max. Starting Pressure with Unloaded Shaft, PSI [bar] at max. pressure Min. Starting Torque, drop cont. lb-in [daNm] Max. Return Pressure without Drain Line, with Drain Line, * Intermittent operation: the permissible values may occur for max. 10% of every minute. ** Peak load: the permissible values may occur for max. 1% of every minute. *** For speeds of 5 RPM lower than given, consult factory or your regional manager. 1. Intermittent speed and intermittent pressure must not occur simultaneously. 2. Recommended filtration is per ISO cleanliness code...

MTK EPMS MOTORS MOTORS R Shaft CO Shaft SB Shaft Shaft Dim. See Page 14 K Shaft Rear Ports Dim. See Page 12 Port A Versions Rear Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW

MTK EPMS MOTORS MOTORS Rear Ports Dim. See Page 12 Standard Rotation Viewed from Shaft End Port A Pressurized - CW Port B Pressurized - CCW Reverse Rotation Viewed from Shaft End Port A Pressurized - CCW Port B Pressurized - CW Type MTKF 160 MTKF 200 MTKF 250 MTKF 315 MTKF 400 MTKF 470 MTKF 500

MTK EPMS MOTORS MOTORS

MTK EPMS MOTORS MOTORS W 4-Bolt flange, Wheel Motor spigot diameter 2.25 in [107,9 mm] - BC 5.81 in [147,6 mm] .25 [6,4] C 4-Bolt flange, spigot diameter 4.99 in [127 mm] - BC 6.375 in [161,92 mm] L5 .72 [18,4] Type MTKC...CO... MTKC...SB... MTKC...R... MTKC...K... MTKC...T... F 6-Bolt flange, spigot diameter 3.25 in [82,5 mm] - BC 4.19 in [106,35 mm] .61 [15,5] Type MTKF...CO... MTKF...SB... MTKF...R... MTKF...K... MTKF...T...

MTK EPMS MOTORS MOTORS SHAFT EXTENSIONS ø1.25” [31,75] srtaight, Parallel key 16 "x 16 "x 1 ¼" Max. Torque 6815 lb-in [77 daNm] 5 Max. Torque 1858.5/1681 lb-in [21/19 daNm] .177/.165 [4,5/4,2] Max. Torque 1858.5/1681 lb-in [21/19 daNm] .157 [4] Max. Torque 1858.5/1681 lb-in [21/19 daNm] .157 [4]

MTK EPMS MOTORS MOTORS PERMISSIBLE SHAFT LOADS The curves apply to a B10 bearing life (ISO281) of 2000 hours at 1 00 RPM. The curves apply to a B10 bearing life (ISO281) of 2000 hours at 100 RPM.

MTK EPMS MOTORS MOTORS MAX. PERMISSIBLE SHAFT SEAL PRESSURE for MTK motors Max. return pressure without drain line or max. pressure in the drain line P bar - continuous operations - intermittent operations MTK Pos.1 - Mounting Flange W - 4-Bolt flange, Wheel Motor spigot diameter 2.25 in - 4-Bolt flange, spigot diameter 4.99 in [127 mm] BC 6.375 in [161,92 mm] - Bolt flange, spigot diameter 3.25 in [82,5 mm] BC 4.19 in [106,35 mm] omit - Side ports E - Rear ports - side ports, 2xG 3/4, G1/4 BSP (ISO 228) - side ports, 2xM27x2, M14x1,5 - 6H (ISO 262) - side ports, 2x1 1/16-12 UN, 7/16-20 UNF...