Text version of the page

Handles —On single, double and triple tier lockers, all parts shallbe chrome plated, die-cast zinc alloy with a tensile strength of not less than 40,000 psi. No moving parts are to operate against out- side surface of locker. Padlock attachment to be integral part of lift which shall be attached directly to locking bar and protected by fixed handle housing. Handle to provide built in padlock strike. Multiple tier lockers shall be equipped with a 16 gauge door pull with padlock attachment when not used with built-in locks. An optional recessed handle shall be available at no extra charge on single tier, double tier, and triple tier. The recessed handle shall be 4

Lyon Locker Specifiers’ Guide - 28115 Heavy Duty Ventilated Locker Specifications

10 51 13/LYO BuyLine 4449

(Knocked Down & All Welded)

CSI Formatted Specifications are available at www.lyonworkspace.com Material General Construction —Prime, high grade Class I mild annealed, cold-rolledsteel free from surface imperfections. A.S.T.M.-1008. Galvannealed steel available for high humidity atmospheres. A.S.T.M.-653. Bolts to be zinc plated or subjected to other rust-retardant treatment.
(All-Welded Only) — All lockers shall be pre-assembled with all seams and joints welded for rigidity and durability. Body —16 gauge steel, flanged to give double thickness of metalat back vertical corners. 18 gauge backs. Door Frame —16 gauge formed steel channels. Vertical membersshall have an additional flange to form continuous door strike.Corners shall be lapped and welded into a rigid assembly. In addi- tion, bottom cross members shall have tang at each end that fits through slot in rear flange of upright frame member to prevent twist-ing out of alignment. Top and bottom cross members shall providesupport for front edge of locker top and locker bottom.
1 �
8 ”w x 6
1 �
16 ”h x 1
1 �
4 ”d and constructed of die cast zinc alloy, nick-el-plated, with a minimum tensile strength of 40,000 psi. Door —One-piece, 14 gauge steel on single, double and tripletier with both vertical edges formed into channel-shaped formation;top and bottom shall be flanged at 90 degree angle. On multiple tier lockers, hinge side shall be formed into channel shaped forma-tion with other three sides flanged at 90 degree angle. Shelves —Single tier lockers shall have one 16 gauge shelfapproximately 9” below top. Flanged on all four sides for strengthwith the front flange turned 45 degrees for safety and attached at no less than two points through each side flange. Only single tierlockers have shelves. Ventilation —Sides and doors shall be punched with diamondshaped perforations. Coat Hooks — Single tier, double tier and triple tier lockers shallhave one double prong hook and three single prong wall hooks. Door Jambs —48” and higher single tier lockers shall have threedoor jambs; double tier and triple tier lockers shall have two jambswelded to side of door frames to engage locking device. Designand gauge of jamb shall prevent freeing of locking device by pry- ing. Each jamb shall have easily replaceable soft rubber bumper.
5 �
8 ” diameter coat rods are standard in 18” and 21” deep knockeddown single tier lockers, replacing ceiling hook. All hooks to be zinc-plated or subjected to a comparable rust retardant treatmentand attached with two bolts. Hinges —Shall be not less than 2” high, .050” steel, 5 knuckle,full loop design forming double thickness on each leaf. Hinges tobe set in slot in door and frame and projection welded to frame and securely attached to door; hinge pin to be spun over at endsto resist removal. Single-tier lockers 48”, 60” and 72” high to havethree hinges. All other tiers to have two hinges – all on right hand side of door. Number Plates —Optional aluminum number plates with etchedfigures at least
3 Quiet Locking Device —Single tier locking device shall engageframe at three points; double tier and triple tier at two points. Channel shaped locking device with full length reinforcing ribs shall be a quiet design utilizing nylon guide inserts to reduce metal tometal contact. The locking device shall include a Zinc alloy latchfinger with a nano roller at point of contact with the door jamb. Lock bar shall be enclosed on three sides and operate within thechannel formation of the door. Locking device shall be prelockingso mechanism can be locked in open position – door locking auto- matically when closed. An optional single point latch shall be avail-able except on 9” wide lockers. Box locker shall have one-pointlocking device with a 14 gauge lock clip for attaching padlock. Doors also to be provided with lock hole filler to permit use of builtin key or combination lock. â�„
8 ” high. All lockers shall have number platesattached near top of door. Standard Finish —Exposed steel parts shall be thoroughlycleaned, given a bonding and rust inhibitive phosphate treatmentand then electrostatically sprayed with a heavy coat of high quality enamel. NOTE: Contact Lyon for finish compatibility with any chemicals. Anchoring —To prevent tipping or injury, Lyon strongly recom-mends that lockers be floor and/or wall anchored. Free-Standing Lockers —Lockers shall be furnished with 6” legs.Optional front and end closed bases available. Recess Trim —End and top recess trim for lockers to be placed inwall recesses shall be 18 gauge formed steel with a 2
3 �
4 ” wideface and shall be bolted to locker frames.Top recess trim to be in approximately 5’0” lengths with a formedsplice cap to cover joints and to hold top recess trim in alignment.End recess trim to be 2
3 �
4 ”higher than lockers and will lap overends of top recess trim for a neat joint at top of corners. NOTE: There are certain sizes and/or types of lockers that areavailable in minimum quantity production runs only. Contact yourLyon factory representative for complete details.

Heavy Duty Ventilated Lockers

Eliminating metal to metal contact, all Lyon locker doorsare fitted with nylon lockbar guides to reduce clangingand provide smoother, quieter operation .In addition to quieter lock bars, Lyon Quiet-Plus lockerdoors have no louvers and include a sound deadening door panel. The resulting combination minimizes noiselevels caused by opening and closing locker doors.
Spec Summary Quiet-Plus LYON strongly recommends wall and/or floor anchoring for all locker installations. • 40,000 psi zinc alloyhandles.• One piece door.• 14 gauge door.• Full loop type hinges. • 16 gauge frame.• All metal locking system.• 16 gauge body partswith18 gauge backs.• Doors and sides shall bepunched with diamond shaped perforations.• Baked on enamel finish.• For overall height, multi-ply number of openings by height listed.• Add 6” to height for legswhen desired. • Built in padlock loop.• Built in key locks orcombination locks are also available.

LIFETIME PRODUCT WARRANTY

9

Specify Lyon!