Models - 6430 - Little Giant Crane & Shovel - #1

CRANE Page 1 of 2

Panel mounted circuit breakers on all major circuits.

Directional signal lights, front and rear with column mounted self-canceling switch. Hazard warning switch.

Sealed beam headlights (high and low beam). Electric horn.

Full D.O.T. compliant light package to include dual tail and stop lights, clearance lights on all four corners, and required reflectors at front rear and both sides.

All tail, stop, and clearance lights to be hermetically sealed, recessed, and mounted in rubber.

All wires to run through a loom and be securely fastened to the frame or body.

Furnished with one (1) dome light.

Automatic backup warning device, Warn 861-C or equal. Furnish all wiring, lights, reflectors, fenders, and mud guards required by State Motor Vehicle Code.

Four (4) out-and-down hydraulic outriggers with controls on both sides of the carrier ground accessible. Optional upper structure cab mounted controls are also available.

Outrigger spread 16 feet, 4-inches wide by 15 feet, 11-inches long with removable 24-inch round outrigger floats. Floats shall be made of aluminum and shall have storage area on the carrier.

Vertical outrigger cylinder stroke 20-inches minimum.

Carrier cab shall be fully enclosed and sound insulated.

Carrier cab shall be equipped as follows:

Tinted safety glass throughout

Grab handles for cab entry

Heater defroster, manufacture's standard. Optional - air conditioning can be supplied.

Windshield wiper and washer

One (1) sun visor

Operator seat to be air suspension type, manufactures standard.

Two (2) exterior rear view mirrors, one (1) each side, heated west coast type, complete with "U" brackets and braced to reduce excessive vibration.

Instrument panel shall include the following illuminated gauges or display the following information on a digital display:

Air Pressure Voltmeter

Engine Oil Pressure Water Temperature Tachometer Fuel Level Hour Meter

An audible warning device for low oil pressure, low water level, and high water temperature, with time delayed automatic shut down.

One (1) 75-gallon side mounted fuel tank. Cap to be attached with a chain.

Front bumper, heavy-duty type. Front bumper to have two (2) heavy duty tow loops attached to frame.

To be 36-inch square angle cord and lattice construction. Basic length 30 feet. Two (2) piece, butt and tip pin connected.

Optional - 5 Ft. - 10 Ft. or 20 Ft. Boom extensions are available

Transmission is to be twin countershaft type with helical gearing and equipped with air controlled countershaft brake to aid during shifting.

Reference: Eaton Fuller RTO11909-MLL or approved equal.

Not required.

Capacity not less than 22,000 lbs.

Eaton EFA 22T or equal

Manufactures standard wheel bearing seals.

Capacity not less than 46,000 lbs.

Single reduction, single speed axle with 6.17 ratio. Eaton DS463-P or equal.

Inter-axle differential with cab controlled lockout.

9 - leaf springs, 3 - inch by 53 - inches with 5 - leaf auxiliary springs, 3 - inch by 35 - inches.

Ground rating not less than 12,000 pounds each.

Hendrickson Bogie with torque rods and equalizer beams.

Suspension to be rated at 46,000 pounds minimum. DRIVE LINE:

Tubular shafts with needle bearing universal joints.

Universal joints between main transmission and forward rear axle to be a minimum of Spicer 1710 series or equal. All universal joints between tandem axle differentials to be a minimum of Spicer 1610 or equal. All shafts will have slip joints.

Integral hydraulic power steering with remote reservoir.

Ross TAS-85 or equal. BRAKES:

Heavy duty full air brakes on all wheels. "S" Cam design. Dana Spicer "LMS" cam operated or equal. Total minimum effective brake area:

Front: 386 square - inches

Rear : 900 square - inches

Parking and emergency spring-type brakes on both rear axles, to be Dana Spicer standard or equal.

Air reservoir tank capacities to meet or exceed D.O.T. 121 requirements. Low air pressure warning buzzer. Illuminated air pressure gauge on instrument panel.

Air compressor, water cooled, and engine oil lubricated. Air supply from engine air cleaner system.

Minimum output 13.5 CFM.

CR industries Turbo 2000 air drier with purge tank or equal.

All air tanks to be equipped with remote, cable actuated drain valves.

Front Wheels: Two (2) 22.5 by 13.00

Rear Wheels: Eight (8) 22.5 by 8.25

Or Four (4) 22.5 by 13.00

All wheels 10 - hole disc type.

Front Tires: Two (2) 425/65R-22.5 (L)

Rear Tires: Eight (8) 12R22.5 (H)

or Four (4) 445/65R-22.5 (H)

Heavy duty 12-volt starting system. Two (2) each calcium 12-volt batteries, maintenance free. Cold crank rating at 0° F of 625 amp minimum each, type 31mf. All batteries to be enclosed in a lockable metal box. Alternator, not less than 100 amps, with not less than 20 amps at 600 RPM.

Crane rated capacity: 30 Tons

GVWR: 68,000 lbs.

GVW: 60,000 lbs.

Wheel Base: 210 - in.

Total Assembled Boom Length: 30 - ft.

Tail Swing: 11'-0"

Travel Length: 54'-6"

Travel Height: 12'-10"

Travel Width (max.): 8'-6"

NOTE: Travel configuration with 30 feet of boom over the front in the boom rest. Three (3) sheave 30 ton hook block required for max. lifts is not supplied.

18 - inch high formed plate box beam - high strength steel frame structure. Triple box cross-section and diagonal stiffeners produce a frame with high resistance to bending and torsional loading.

RBM 20,204,650 in/lbs. S.M. 202.046

Diesel 6 - cylinder, four-cycle high torque rise with exhaust driven turbocharger, and after cooler. Piston displacement not less than 504 cubic-inches.

Peak torque not less than 660 ft/lbs. at 1,300 RPM. Gross horsepower not less than 240 at 2,400 RPM. Cummins 8.3T standard - optional engines available.

Engine block heater to aid during cold weather starting.

Air cleaner to be a Donaldson, two-stage dry type with dash mounted restriction indicator, color-coded. Air cleaner to be engine manufacture approved.

Oil filters, spin-on, full flow two (2) each, minimum.

Engine mounted fuel/water separator.

Vertical muffler and exhaust. Exhaust system shall be fully compatible with engine and engine manufacturer approved. Exhaust to terminate with manufacturer choice of rain cap or 90° elbow to minimize the possibility of rain entering the exhaust system. Muffler as required for proper noise suppression.

Radiator, heaviest duty shutter-less cooling system available. All radiator, after-cooler, oil cooler, and heater hoses to be manufacture standard.

Coolant recovery system per engine manufactures requirements.

Clutch to be a minimum of 15 inch heavy-duty double plate, self-adjusting, or equal.

15-1/2 inch normal torque rating of 1,250 FT./LBS.

Shall be 11 - speed manual. Transmission to have a magnetic drain plug.

Ratios: Forward

LL1 - 26.08 to 1 L - 16.03 to 1 LL2 - 11.85 to 1 1^st - 7.41 to 1 2^nd - 5.23 to 1 3^rd - 3.79 to 1 4^th - 2.77 to 1 5^th - 1.95 to 1 6^th - 1.38 to 1 7^th - 1.00 to 1 8^th - .73 to 1 Ratios: Reverse

LL - 25.22 to 1 L - 15.76 to 1 H - 4.15 to 1

Max Gross Input Torque: 1150 Ft.Lbs.

Speed at engine RPM. Of 2,400 is 66 MPH.