LMX+ Series - LITRE METER - #1

Text version of the page

LMX+ Series Inline Pelton Wheel flowmeter with integral flow straighteners, providing a pulse output. Model Type Flow Rate Range Pressure Drop LMXS.003 or LMX.003* 0.004 to 0.060 l/min 0.18 bar @ 0.03 l/min; 0.7 bar @ 0.06 l/min LMXS.005 or LMX.005 0.006 to 0.100 l/min 0.18 bar @ 0.05 l/min; 0.7 bar @ 0.10 l/min LMX.01 0.01 to 0.25 l/min 0.33 bar @ 0.125 l/min; 1.3 bar @ 0.25 l/min LMX.05 0.02 to 1.3 l/min 0.18 bar @ 0.65 l/min; 0.74 bar @ 1.3 l/min LMX.24 0.03 to 4.3 l/min 0.3 bar @ 2 l/min: 1.2 bar @ 4.3 l/min LMX.45 0.04 to 6.3 l/min 0.23 bar @ 3 l/min: 1.3 bar @ 6.3 l/min LMX.48 0.06 to 8 l/min 0.30 bar @ 4 l/min: 1.2 bar @ 8 l/min LMX.90 0.08 to 15 l/min 0.25 bar @ 9 l/min: 0.7 bar @ 15 l/min LMX.220 0.1 to 28 l/min 0.24 bar @ 10 l/min: 1.8 bar @ 28 l/min LMX.12.5 1 to 65 l/min 0.2 bar @ 32l/min: 0.9 bar @ 65 l/min *Lower flows on request Common Features: Pressure Rating LMXS.003 & 005 30bar LMX. 100bar Temperature Rating 100° C Viscosity Range Up to 10 cPs; ring factory if higher Accuracy ±2% of actual reading for the top 90% of range. ±0.5% FSD for the bottom 10% of range. [003 and 005 linearisation required] Repeatability ±0.2% reading over top 90% of range Pipe Size LMXS.003 and 005 LMXS: 8mm OD tube for optional Swagelok fittings to ¼" NPT, ¼" BSP. Other options available on request. LMX: ½”NPT and BSP normally in stock. LMX. 1/2” BSP or NPT male (Specify at time of order) End to end length/Weight 180mm. LMXS003 and 005 can be reduced in length to 80mm; less than 2kg Body and Internals 316SS with Teflon PFA rotor and sapphire/sapphire bearings, sealed ferrites on rotor Seal PTFE Gasket (LMXS003 and 005 use FPM O ring) External materials of sensing electronics 316SS or 303SS and anodised aluminium Output & Power NPN open collector with 4-way M12 sensor connector [IEC-61076-2-101] – e.g. compatible with Brad Harrison, Hirschmann, ERNI and Turck Banner. Supplied with 5m cable – bare ends. 8 to 28Vdc input. Options: Output PNP or TTL (identified by green or blue cap respectively). Also divide by 2, 4 or 10 function Connections Plain OD pipe for butt welding (as on LMXS) or flanges available in alternate styles Flow rate, temperature and pressure Alternate ratings available in different sizes and styles, consult factory for further details Seals FEP covered Silicon, EPDM or Kalrez® for chemical protection IS Hazardous Area Version ATEX Available in alternate styles to EEx ia IIC T5 – consult factory for further details (limited to process temperatures up to 70°C) Consult factory for input and output data. Housed in an IP65 epoxy coated die-cast aluminium body-mounted enclosure with 5pin DIN socket. SB or BB IS Electronics pickup For use either when instrumentation is also included in the hazardous area or an M20 gland is required. Body-mounted stainless steel or Naval Brass IP68 enclosure, one or two M20x1.5 gland entries. Documentation: Operating and Maintenance Manual LM0093 with General Information LM0092 Installation Drawing C5220 Conformity: These products conform to PED and EMC. ATEX option available. Flowmeter Specification Sheet