AIRMIX® and AIRLESS spraying equipment - KREMLIN REXSON - #29

/ 48


catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
Pages:


See other catalogues for KREMLIN REXSON

Text version of the page
• Flat tips
CO CO LU
<
Q.
c
CS
(ft re
3
.
Flat tips ensure high precision and performance
Part number: 000 00 XX.XX (replace of the X by the number read on the table)
FLAT TIPS
Fluid output at 140 bar (l/mn)
Equivalent diameter (in mm)
Tip Diaphragm
Filter in handle (MESH)
Angle
Width of fan (cm)
18° 8
30°
13
40°
18
50°
23
60°
28
67°
33
75°
38
82°
43
88°
48
94°
53
0,230
0,18/0,007
12
red (200)
03.03
03.05
03.07
0,310
0,23/0,009
12
red (200)
04.05
04.07
04.09
04.11
0,460
0,28/0,011
12
blue (150)
06.05
06.07
06.09
06.11
06.13
0,630
0,33/0,013
15
blue (150) blue (150)
Number engraved
09.05
09.07
09.09
09.11
09.13
09.15
-
-
-
1,010
0,41/0,016
18
on the tip
14.03
14.05
14.07
14.09
14.11
14.13
14.15
14.17
-
1,500
0,50/0,020
20
yellow (100)
20.05
20.07
20.09
20.11
20.13
20.15
20.17
20.19
-
2,250
0,61/0,024
25
yellow (100)
30.07
30.09
30.11
30.13
30.15
30.17
30.19
-
3,340
0,73/0,029
33
white (50)
45.07
45.09
45.11
45.13
45.15
-
45.21
Using a diaphragm increases spraying fineness.
Part number: 000.029.1xx (replace the crosses with the diaphragm number)
• Tips with adjustable fan
Tips with adjustable fan allow you to adjust fan width and output simultaneously by operating one control knob.
TIPS WITH ADJUSTABLE FAN
Equivalent size in flat tips minimum maximum
Size(mm)
28 41
Tip with fixing screw (M250) P.N.
100.000.620 100.001.468
Spare needle P.N.
000.000.621 000.001.469
006 014
020 068
KREMLIN'S advice
Good quality spraying depends on the condition of the tip. Regularly replacement of the tip ensures a consistent fan pattern.
Any overuse of tips will result in an oval-shaped outlet forming, which creates two major problems :
- Reduced width of fan, with fluid heavily concentrated in the centre
- Higher fluid output.

pageCatalog pdf di En 2012-05-22-30