Operatioin manual E - KLT Co.,Ltd. - #1

Text version of the page

ffcCi.smil.UBE E Pulsarlube E Grease Sélection Guidelines USER MAIS Cost Effective, User Friendly Automatic Single Point Lubricator Grease PL1 Multi Purpose High performance NLGI #2 grade PL2 Heavy Duty Excellent heavy duty NLGI #2 with high viscosity base fluids and additional load carrying capacity PL3 High Speed High performance NLGI #1 grade PL4 H1 Food Grade USDA H1 NLGI #2 grade for applications where food grade product is required PL5 High Temperature Synthetic high performance NLGI #2 grade with oxidation stability PL6 Multi Purpose MoS2 Dark gray colored MoS2 containing mineral based product fortified extreme pressure property PL7 Low Temperature Fully synthetic product for extreme low temperature applications Specifications Grease Capacity 120cc Max operating pressure 5kgf/ctif (70psi) Operating Temp Range -20°C ~ 60°C (-4T ~ 140T ) Product Size 077mm (3.03") x 112mm (4.41") Installation Thread Size 1/4" Male NPT & BSP compatible Gas Type Nitrogen (N2) Gas Available Dispensing Periods 1, 3, 6, 9 & 12 months Certifications / IP code CE / IP65 Remote Installation upto 1m(3ft ) using a 8mm(5/16") O.D. pre-filledlube line OEM filling is available upon request under special terms and conditions. Please contact your local distributor or manufacturer. How to dispose ^NOlt Technical information is subject to change without prior notice. Models PULSARLUBE E120/120cc Grease Lubricator Before Use- ISO9001/14001 Ci Thank you for purchasing the Pulsarlube E, from Pulsarlube USA, Inc. To ensure the safe operation and proper installation of the Pulsarlube E unit, we strongly recommend that you read the following information carefully before use. If you require further information, please contact your local supplier or manufacturer. 1. Turn the housing cap counterclockwise and unscrew the top to remove the battery cover. Dispose of used battery pack conforming to local regulations. 2. Using a hand tool such as screw driver, detach the PCB (Printed Circuit Board) from the used unit. Dispose of the PCB conforming to local regulations. 3. Dispose of remaining plastic components in a designated area. Comply with local regulation for recycling. 4. Do not cut or puncture a used unit to avoid any potential personal injury or hazards. Product Details | How to set Pulsarlube E It is very intuitive and simple to set the Pulsarlube E unit. The Pulsarlube E ensure an error-free operation with five selectable preset dispensing periods; 1, 3, 6, 9, and 12 months. Shelf Life and warranty period Housing Cap Battery Cover Battery Mode Selector PCB N2 Gas Generation Cell Piston Lubricant Reservoir Grease Base 1/4" NPT/BSPT available Thread Pressure Relief Valve The shelf life of each Pulsarlube E unit is 2 years from the date of production. Product warranty is limited to original defects in material and workmanship and will not cover any collateral damage due to mishandling, abuse and /or any other inappropriate use of this product. Warranty period is 1 year from the date of purchase. | How to order E120 / PL1 1 ^ m \ 1 + mm + ' E ^^^^^^^^^^^^^^ ■ ^1 "w 6 W -Grease Type -Lubricator Model (Pulsarlube E Model E120 : 120cc Capacity) Q) Pulsarlube USA, Inc. 4312 DiPaolo Center, Glenview, IL 60025, USA TEL: 1-847-795-0591 FAX: 1-847-795-0119 www.pulsarlube.com / info@pulsarlube.com Doc No. 1122-000 REV. 120100 Protector A To lock the Pulsarlube E unit, the ^ on the housing cap Must be located in the area shown above (#5).