Catalog excerpts
Swash-plate Type Axial Piston Pumpsfor Open Circuits in Industrial Vehicles >
Open the catalog to page 1CAUTION DANGER CAUTION WARNING CAUTION WARNING CAUTION CAUTION > CAUTION CAUTION WARNING > WARNING CAUTION CAUTION CAUTION CAUTION CAUTION CAUTION >
Open the catalog to page 31. High Power Density 3. Long Life > A lighter and more compact machine with higher pres- sure rating and increased power density (output pow- er/mass) was obtained by adopting a half log type swash plate.In particular, the double pump with its tandem ar-rangement, has eliminated a power divider, has an in- creased transmission efficiency, and is lighter. A long life is obtained by adopting main bearings of large capacity and the piston-return mechanism that compensates for the wear of the shoe. 4. Low Noise > Even less noise has been achieved because of the op- timum design of the valve...
Open the catalog to page 5The pump shaft should be mounted in the horizontal direction as shown in the figure below.The drain line loop must be extended above the top of the pump case. The upper drain port should be used, and the drain pipe size must be equal to or larger than the drain port size.In case of the pumps with centrifugal pump, the drain lines must be settled on each pump. > Front pump Rear pump Tandem pump For satisfactory service life of these pumps in application, the operating fluid should be continuously fiitered to keep at least the > Examples of using a filter cleanliness level of NAS 1638 Class...
Open the catalog to page 13Please use a flexible coupling for connection of the pump drive shaft with an engine flywheel or an electric motor shaft.Alignment should be so carried out that the parallel error may be held with in 0.03 mm.Do not put a radial or thrust load at the shaft end. > Before starting-up, fill the pump case with system fluid through the case drain connection. Case must remain full of fluid to provide internal lubrication. > Please be careful so that the drain pressure in the casing does not exceed 0.1 MPa normally and 0.4 MPa at its peak.A suitable size of drain hose and drain filter should be...
Open the catalog to page 14OVERSEAS OFFICES Seoul Office > c/o Kawasaki Machine Systems Korea, Ltd. 3rd Floor (307), Industrial Complex Support Bldg., 637, Kojan-Dong, Namdong-Gu, Incheon, 405-817, KoreaPhone: 82-32-821-6941Fax: 82-32-821-6947 Beijing Office > Room No.2602, China World Tower 1, China World Trade Center, No.1 Jian Guo Men Wai Avenue, Beijing 100004, People's Republic of ChinaPhone: 86-10-6505-1350Fax: 86-10-6505-1351 Shanghai Office > 13th Floor, HSBC Tower, 101 Yin Cheng East Road, Pudong New Area, Shanghai 200120, People's Republic of China Phone: 86-21-6841-3377Fax: 86-21-6841-2266 Taipei Office >...
Open the catalog to page 15All Kawasaki Precision Machinery catalogs and technical brochures
-
HPB Series
76 Pages
-
M3X/M3B
35 Pages
-
HPC Series
37 Pages
-
HMC Series
43 Pages
-
K3V/K5V/K7V
8 Pages
-
HMB Series
92 Pages
-
K3VL Series
76 Pages
-
PV series
2 Pages
-
ERU series
2 Pages
-
HMF Series
72 Pages
-
M7V / M7X Series
64 Pages
-
HPC Series
37 Pages
-
KPM-PV
2 Pages
-
KDRDE KWE series
2 Pages
-
KTEM/ KTMS series
2 Pages
-
K3VL Series
72 Pages
-
HMF Series
72 Pages
-
KMP series
2 Pages
-
ERU series
2 Pages
-
K7VG
32 Pages
-
K8V
36 Pages
-
K3VLS
36 Pages
-
KLSV 18
24 Pages
-
KPES
2 Pages
-
HPC400
4 Pages
-
hydraulic industriel vehicle
20 Pages
-
B - Brake Valve
24 Pages
-
M-Motor
35 Pages
-
CBD - Counterbalance Valve
6 Pages
-
M2X/M5X - Slewing motor
19 Pages
-
Axial Piston Pump Series K3VG
34 Pages
-
K3VG Series
34 Pages
-
HMC-capability-brochure
6 Pages
-
High-Power-HPC-Series-Datasheet
44 Pages
Archived catalogs
-
HMB
70 Pages
-
HMC CATALOGUE
60 Pages
-
Rotary Actuator HR Series
8 Pages
-
B-motor-catalog-
70 Pages
-
Datasheet - K3VL B Series
53 Pages
-
THE K3VLB-SERIES
6 Pages
-
High Power HPC Series
40 Pages
-
Axial piston hydraulic motors
35 Pages