BLOCKS FOR MC - Kanetec - (Version JPG) - PDF Catalogue | Technical Documentation

BLOCKS FOR MC - Kanetec - #1

Separator, Magnetic base, Magnetic plate, Magnetic separator, Vacuum chuck

Separator, Magnetic base, Magnetic plate, Magnetic separator, Vacuum chuck

See other catalogues for Kanetec

Text version of the page

BLOCKS FOR MC_

WM*H7T9 MAGNETIC FIXTURE BLOCK

(An example of usage)

JMC I EPB

(An example of installation)

[An example of application)


	pi;

			._I

JMC-120

Held by magnetic force

Table

Clamped or bolted from table

Table

Permanent magnetic blocks to hold workpieces strongly on machines.

Two types of clamping are available; magnet type and mechanical

type by use of threaded holes.

[Features]

•A permanent magnet used produces strong magnetism. •The workpiece mounting and dismounting time can be reduced significantly.

•Iron and nonmagnetic workpieces can be held by a magnet and mechanical clamping.

•These blocks can be connected to allow relatively large work-pieces to be set.

•The blocks can be mounted vertically by using threaded holes on three faces (both sides and bottom) other than the attractive face.

H 8-M thread, depth D

\2X4-M thread, depth D

B-M thread, depth D

[mm (in) ]

Side Face

Holding Face

Mounting Face

Others

Height

Holding Power

¿1

7.5kN 136 180 59 77 134 SO 70 50 11 124

(750kgf) (5.35) (7.08) (2.32) (3.03) (5.27} (3.15) (2.75) (1.96) 10 (0.43) (4.88)

12kN 180 198 78 87 178 100 80 48 (0.39) IS 168

(1200kg0 (7.08) (7.79) (3.07) (3.42) (7.00) (3.93) (3.15) (1.89) (0.62) (6.53)

B0 244 11 M10 15

(3.15) (9.60) (0.43) (0.39) (0.59}

125 284 13 M12 IB

(4.92) (10.3) (0.51) (0.47) (0.70)

145

(5.70) 192 (7.55)

JHC- 75

25kg/ 55 lb

50kg/110lb

n. The rwkJIng power applies to SS400,50 mm thick, ground surface held on whole lace. 2. An operating handle Is Included. The connecting parts are optional. . When several blocks are connected and the same faces are used, ground them together after connecting blocks to obtain a required flatness.

Model EPB

PERMANENT ELECTROMAGNETIC BLOCK

(An example of usage)

[Application]

These blocks are designed for holding workpieces on such machines as machining centers and NC machine tools. Suitable for machining workpieces by 5-face machining centers, etc. [Features]

•By securing a workpiece overhanging, the 5-face machining center setup time can be shortened.

•These blocks can be used in wet operations and therefore can be used like normal magnetic chucks.

•Since these blocks are of permanent electromagnetic type, the holding power is not affected by power failure or cable breakage. Also since very little heat is generated, thermal Influence on workpiece is minimal.

•The metal connecting joint facilitates disconnection of the power cable. (Pallet change and external setup supported.)

[mm (in)]

Chuck controller required additionally


Model	Dimensions			Pole	No.of	Holding	Mass	Electro
Model	Width	Length	Height	Size	Poles	Power	Mass	Chuck Master
EPB-1525	164	riTfl *(ft* OjO	150 (5.90)	50 (1.96)	2	12.5kN	40ko/ 88
EPB-2525	250(9.84)	¿üü 19.S4J			4	25kN	60kg/	EPS-P2100A
EPB-3636	350	350			9	57kN	120kg/264

55:

^Turning the permanent electromagnetic chucks on and off must be limited to once per several minutes, on/off operations are repeated frequently, the chucks may be damaged by overheat

Iii

CM