Standard Gas Springs & Mounts - KALLER - (Version JPG) - Page n° 15 - PDF Catalogue | Technical Documentation

See other catalogues for KALLER

Punching unit, Cam, Spring, Gas spring

Text version of the page

2.2/4

EPS2 24 20 - 170

EPS2 24 (Ejector Pin Special with an M24 thread). It is available with four pre-set models. Each model is colour-coded for easy identification of force rating. If needed, these models can be recharged or adjusted to meet individual force requirements.

Also available is a model (black) which is delivered with a precharge of 5 to 10 bar, intended to be adjusted to the desired force.

The EPS24 is based on FORDS WDX3580-19XX XX XX gas spring standard. Please note that Ford's colour-code scheme may differ from the one shown here.

cu E ai ai

o o

How to order

EPS2 24 20-10

- Stroke Length (mm)

(10, 16, 20, 25, 30, 38, 40, 50, 60, 70, 80, 100, 125)

- Force: 20 = Green

40 = Blue 80 = Red 170 = Yellow

xx = Black, delivered with a pre-charge of 5-10 bar

Model: -


S Stroke	End force in N at + 20°C, at full stroke				L ±0.25		Gas vol. (l)	Weight (kg)
S Stroke	EPS2 24 20	EPS2 24 40	EPS2 24 80	EPS2 24 170	L ±0.25	L min	Gas vol. (l)	Weight (kg)
10	325	650	1220	2435	65	55	0.05	0.153
16	366	733	1374	2748	77	61	0.06	0.164
20	360	720	1345	2690	85	65	0.07	0.172
25	389	778	1459	2918	95	70	0.08	0.182
30	375	750	1410	2815	105	75	0.10	0.192
38	407	814	1527	3054	121	83	0.11	0.206
40	385	770	1445	2890	125	85	0.12	0.211
50	420	835	1565	3130	145	95	0.14	0.230
60	420	840	1570	3140	165	105	0.17	0.249
70	420	840	1575	3150	185	115	0.19	0.268
80	420	840	1580	3155	205	125	0.22	0.287
100	420	845	1580	3165	245	145	0.26	0.325
125	420	845	1585	3170	295	170	0.32	0.372

X LU I


Model	Force in N at +20°C	Colour	Charging pressure (bar)
Model	Initial	Colour	Charging pressure (bar)
EPS24 20	230	Green	20
EPS24 40	450	Blue	40
EPS24 80	850	Red	75
EPS24 170	1700	Yellow	150
EPS24 XX*	230-1700	Black	20-150

* Force to be set by the customer. Delivered with a pre-charge of 5-10 bar.

BASIC INFORMATION

MOUNTING POSSIBILITIES

For general information see "About gas springs", 2.1

Pressure medium...........................Nitrogen

Max. charging pressure.................180 bar

Min. charging pressure..................6 bar

Operating temperature...................0 - +80°C

Force increase by temperature......± 0.3%/°C

Recommended max strokes/min ... ~ 30-80 (at 20°C) Max piston rod velocity..................1.6 m/s

Rod surface....................................Nitrided

Tube surface ..................................Black Oxide

Repair kit........................................ Non-repairable

2rt I A We reserve the right to add, delete or modify

■ 2/^ ■m#%^H^H^H^m components without notification.

by Strömsholmen AB All dimensions are stated in mm.

Edition 6 / May 2005 ₊4g 140 571 00 • WWW.kaller.com All dimensions are nominal unless tolerance is stated.

Standard Gas Springs & Mounts - KALLER - #15

Punching unit, Cam, Spring, Gas spring