Text version of the page

ORDERING INFORMATION (continued)

/f Electronic Module With 1 ea. Analog Output (continued) M4A One level, with LCD indicator, and Communications
1,2,3,4 M4B Two levels, LCD indicator, and Communications
1,2,3,4 M5A One level, one temperature point, LCD indicator, and Communications
1,3,4,5 M5B Two levels, one temperature point, LCD indicator, and Communications
1,3,4,5 Notes: 1. Default Communication is HART Protocol 2. Add “D” suffix to module option for Honeywell DE (class 0 support) 3. Add “F” suffix to module option for Foundation Fieldbus ITK 4.01 compliant 4. Add “S” suffix to module option for 20 Point Strapping Table (not available with “D” suffix) 5. Not available with HP, H3, SW1 or SW3 options. /g Second Analog Output X None RI Second electronic module with 1 ea. Analog output and LCD indication
Notes: 1. Not available with M1, M2 & M3 Module types 2. Only for use with HART Protocol equipped electronics modules 3. The RI100 is only approved as an Explosion Proof device 4. Analog output field selectable to any of the two levels or temperature 5. Housing type will be same as primary transmitter housing (/c above) /h Approvals
1,2 FM Factory Mutual CSA Canadian Standards Association CEX ATEX Flameproof CEI ATEX I.S. IEI International Electromechanical Commission I.S.
0539 0036 GR GOST Russia
Notes: 1. All Explosion Proof Approvals exclude Probe F1 and SW3. 2. All Intrinsically Safe Approvals exclude RI (secondary analog output) & Honeywell DE options. /i Process Connection X None
(use with /SW1, /SW2 and /SW3 probe types) CF Standard adjustable compression fitting 3/4” MNPT
(1”MNPT with /F1 probe type) FL Flange or plug (shipped loose) with FNPT thread for use with compression fitting
(specify type, material and rating from SLG-0001-1 Flange Designation Chart) WP Flange or Plug welded to the sensor tube without compression fitting
(specify type, material and rating from SLG-0001-1 Flange Designation Chart) /j Float Type X None
(Use this selection with /SW1, /SW2, & /SW3 probe types) Fnn Selection from Standard Float Chart (SLG-0003-1) or specify /FXX for custom float /k Insertion Length L
Specify inserted length from process connection to end of probe in inches or millimeters or meters Consult factory for ML, L1 & L2. There is an unusable range of 2.5 inches minimum (12” for /F1) at the bottom of the sensing tube (which can be reduced depending upon float dimensions). The unusable range at the top of the sensor tube will be affected by the float dimensions. NOTE: Consult factory for special application requirements. Available Accessories: M20 ISO FITTING: M20 Female Electrical Connection ( MM - Brass or MMS - Stainless Steel) For fastest response to inquiries provide a completed AT100 Application Data Sheet or the Serial Number of an existing AT100. QuikShip ORDERING INFORMATION QuikShip transmitters with the following model number are available for shipment in 1-5 working days . No deviation from the QuikShip model number will be accepted. Model Number: AT100/S6/LW/A/R1/H0/M4A/X/ “approval” /CF/ “float” / “L” QuikShip # “L” dimension QuikShip # “L” dimension AT100QS1 15.3" (389mm) AT100QS5 63.3" (1608mm)
Replace the word “approval” with the required approval code: FM, CSA, CEX, CEI, IEI, or GR Replace the word “float” with one of the following AT100 QuikShip floats: F1B, F2B, F17B, or F15B. AT100QS2 27.3" (694mm) AT100QS6 75.3" (1913mm) AT100QS3 39.3" (999mm) AT100QS7 87.3" (2218mm) AT100QS4 51.3" (1303mm) AT100QS8 99.3" (2523mm)
K-TEK 18321 Swamp Road Prairieville, Louisiana 70769 USATelephone: (1) 225-673-6100 Fax: (1) 225-673-2525 AT100-0202-1 Rev L (06-2007) DCN0132 For latest version of this data sheet, visit www.ktekcorp.com. Email: sales@ktekcorp.com Website: www.ktekcorp.com