video corpo

Versacutter - Mobile Waterjet Cutting System
3Pages

{{requestButtons}}

Catalog excerpts

Versacutter - Mobile Waterjet Cutting System - 1

hydraulic versacutter Jet Edge’s Hydraulic Versacutter is a portable abrasivejet cutting and beveling system. Rigid and flexible tracks allow the Hydraulic Versacutter to operate on flat or curved surfaces. The system is used in a variety of cutting applications including pipelines, steel reinforced concrete, reactor vessels and fabricated metal structures. It is especially suited for cutting in hazardous zones where flames and heat are restricted. The Versacutter carriage is a sealed unit that contains a hydraulic motor. The hydraulic motor is connected to a gear reducer and a drive sprocket. The sprocket engages the track to drive the carriage along the track. Guide wheels support the carriage by clamping it onto the track. A lever retracts the drive sprocket so the drive unit can be positioned freely on the track and extends the drive sprocket to engage the holes in the track. The carriage has several clamps and tubes to adjust the position of a cutting head. The Versacutter includes two 8’ sections of track; one rigid, one flexible. Additional track sections can be connected up to any desired length, limited only by the reach of the support equipment hoses. Track sections are bolted together for extended cuts. The rigid track is used of flat surfaces. The track is stiffened with two support rails. Mounting plates can be attached to the support rail allowing the track to be bolted to a surface. The flexible track is used on cylinders and undulating surfaces. A winch is mounted to one end of the track. A cable connects to the end of the track and the winch. The flexible track is mounted to standoffs and magnetic standoffs; the magnetic standoffs work on ferrous surfaces. A pneumatic delivery system meters the abrasive from the hopper to the cutting head. The micrometer controlled slidegate measuring device features a large readout dial and a positive setting lock for accurate and repeatable abrasive delivery. The hopper holds up to 400 pounds of abrasive for hours of uninterrupted cutting. Quick setup and maneuverability are achieved by mounting the hopper on pneumatic tires, and the weight-saving design enables operation in difficult overhead and vertical applications. Carriage Dimensions Height: Width: Length: Carriage Weight: Track Weight: Magnetic Standoff: Movement Speed: Hydraulic Supply Pressure: Flow: 9-1/2 in (241 mm) 9-1/32 in (230 mm) 14-7/8 in (378 mm) 23 lb (10.4 kg) 32 lb (14.5 kg) per 96 in (2438 mm) track section 70–80 lb (32–36 kg) holding power 0–7.5 ipm (0–190 mm/min) 1500 psi (103 bar) 1–4 gpm (4.5–18.2 lpm) powered by jet edge! The Riding Deckblaster is powered by a Jet Edge waterjet intensifier pump. Model iP55-280DS

Open the catalog to page 1
Versacutter - Mobile Waterjet Cutting System - 2

hydraulic versacutter Operation Movement ForwardStopReverse The Hydraulic Versacutter is operated by a remote control unit. The remote control unit is designed to hang on the rear brace of the abrasive hopper. The remote control unit includes several valves to control the operation of the hydraulic cutting package: High Flow Hopper Speed Control Emergency Stop Switch Remote Control Unit FORWARD ON EMERGENCY STOP Abrasive On/Off • A three-position valve ports hydraulic fluid to the hydraulic motor to move the carriage forward, reverse, and stop movement. • Two flow control valves adjust the...

Open the catalog to page 2
Versacutter - Mobile Waterjet Cutting System - 3

hydraulic versacutter Hydraulic Versacutter Controls A three-position valve selects the movement of the Hydraulic Versacutter. The valve stays in the set position. The middle position stops the Hydraulic Versacutter movement. A two-position valve turns the ultra high pressure water on and off. Speed Control: Two flow control valves (one on the front, one on the back) adjust the hydraulic flow that sets the forward and reverse speeds of the Hydraulic Versacutter. Abrasive Control: A two-position valve controls the compressed air supply that operates the abrasive supply from the hopper. The...

Open the catalog to page 3

All JET EDGE catalogs and technical brochures

  1. deckblaster5

    1 Pages

  2. Rail-Gantry

    1 Pages