MD-F, MD-V
10Pages

{{requestButtons}}

Catalog excerpts

MD-F, MD-V - 1

IWAKI MAGNETIC DRIVE PUMPS MD-F MD-V Main material MD-F: CFRETFE MD-V: CFRPVDF Solutions for chemical handling applications

Open the catalog to page 1
MD-F, MD-V - 2

Compliant with highly corrosive / viscous liquids High-end compact magnetic drive pumps Most chemicals can be handled including strong acid/alkaline. High corrosion-resistance Viscosity responsiveness The combination of the MD-F series with CFRETFE wet ends The MD-F series is designed to pump highly viscous liquids and the MD-V series with CFRPVDF wet ends covers most such as strong acid. Three types of impellers are selectable chemicals including strong acid/alkaline. according to liquid viscosity. MD-15F(X/Y)·30F(X/Y) • Max Discharge capacity 9 - 13 l/min 3-8m • Max Discharge head 1...

Open the catalog to page 2
MD-F, MD-V - 3

IWAKI MAGNETIC DRIVE PUMPS Leak free Easy maintenance Magnetically-driven seal-less pumps are free from leak problems The pump unit is comprised of a small number of subunits, so and the need of seal replacement. This feature and its compact that maintenance is significantly eased. nature offer the best fit in built-in applications. md-15rV*20rzV*30(r/rz)V fT! md- 70(r/rz)V ™ • Max Discharge capacity 10 - 32 l/min • Max Discharge capacity 40 - 86 l/min • Max Discharge head 2.4 - 8.0 m • Max Discharge head 6.7 - 14.3 m

Open the catalog to page 3
MD-F, MD-V - 5

IWAKI MAGNETIC DRIVE PUMPS Construction Motor Drive magnet The 6- or 8-pole high power ferrite magnet drives the impeller over the rear casing. Rear casing O ring CFRETFE single-piece rear casing of the MD-F and CFRPVDF single-piece rear casing of the MD-V. The bearing is placed at the bottom, supporting the spindle. Impeller Spindle MD-F CFRETFE single-piece closed impeller. Three impeller types (X/Y) are available according to specific gravity. Front casing MD-F CFRETFE injection mold of the safety thread connection type MD-V CFRPVDF hose connection is available as well as thread...

Open the catalog to page 5
MD-F, MD-V - 6

md-15F(x/y)*30F(x/y) • Range of Max. discharge capacity: 9 - 13 L/min • Range of Max. discharge head: 3 - 8 m • Temperature range: 0 - 80°C (Contact us for applications below zero.) • Limit of viscosity: 30 mPa-s (at 1 S.G.) • Ambient temperature: 0 - 40°C • Motor type: Capacitor-run induction motor Pump identification Material of O ring No mark: FKM (Standard) E: EPDM (Special order) Motor 220/240: 220/240 single Iliustiation shows model MD-30F Impeller X: Low S.G. type Y: Middle S.G. type

Open the catalog to page 6
MD-F, MD-V - 7

IWAKI MAGNETIC DRIVE PUMPS MD-F MD-V md-55F(x/y)* 100F(x/y) c tff r Range of Max. discharge capacity: 60 - 125 L/min Range of Max. discharge head: 5.4 - 10.5 m • Temperature range: 0 - 80°C (Contact us for applications below zero.) • Limit of viscosity: 30 mPa-s (at 1 S.G.) • Ambient temperature: 0 - 40°C Pump identification Note: Specify the pump model and power specification at an inquiry phase. Iliustiation shows model MD-100F Available with IEC frame motors This type of unit allows the pumps to be supplied with numerous motor options.

Open the catalog to page 7
MD-F, MD-V - 8

• Temperature range: 0 - 80°C (Contact us for applications below zero.) • Limit of viscosity: 30 mPa-s (at 1 S.G.) • Ambient temperature: 0 - 40°C • Motor type: Capacitor-run induction motor Note: The union field shows the nominal diameter of the applicable VP vinyl chloride hose. Heat resistance of the standard union is 0 - 55°C Pump identification Impeller CFRPVDF Front casing CFRPVDF PTFE / CFRPPS Alumina ceramic Type R: Standard type RZ: High head type Material of O ring No mark: FKM (Standard) E: EPDM (Special order) IIIustlation shows model MD-30RZV Note: Material of bearing for...

Open the catalog to page 8
MD-F, MD-V - 9

md-70(r/rz)VRange of Max. discharge capacity: 40 - 86 L/min Range of Max. discharge head: 6.7 - 14.3 m Specifications (50Hz) • Temperature range: 0 - 80°C (Contact us for applications below zero.) • Limit of viscosity: 30 mPa-s (at 1 S.G.) • Ambient temperature: 0 - 40°C Note: The union field shows the nominal diameter of the applicable VP vinyl chloride hose. Heat resistance of the union is 0 - 55°C Pump identification Thrust ring Alumina ceramic Bearing PTFE IMustlation shows model MD-70RV Note: Specify the pump model and power specification at an inquiry phase. Note: Material of...

Open the catalog to page 9
MD-F, MD-V - 10

IWAKI MAGNETIC DRIVE PUMPS Special accessories • Union joint Special-purpose union joints are available to cope with three types (13mm, 16mm and 20mm dia.) of piping. Tight sealing O-rings are used to prevent thread damage caused by over-tightening. Specifications Model IWAKI CO., LTD. 6-6 Kanda-Sudacho 2-chome Chiyoda-ku Tokyo 101-8558 Japan TEL : (81)3 3254 2935 FAX : 3 3252 8892 EUROPE ASIA / OCEANIA / NORTH AMERICA / SOUTH AMERICA European office : IWAKI Europe GmbH Holland : IWAKI Europe (NL Branch) Belgium : IWAKI Belgium N.V. Denmark : IWAKI Nordic A/S Finland : IWAKI...

Open the catalog to page 10

All IWAKI Europe GmbH catalogs and technical brochures

  1. TC-X

    28 Pages

  2. IX-B

    8 Pages

  3. MEK

    5 Pages

  4. MMP

    2 Pages

  5. MP series

    2 Pages

  6. MTFO

    2 Pages

  7. IX-C/D

    12 Pages

  8. NRD/RD

    4 Pages

  9. SMX-F

    8 Pages

  10. EJ-R

    2 Pages

  11. EWN-W

    2 Pages

  12. V

    8 Pages

  13. Serie MDW

    8 Pages

  14. MDE

    8 Pages

  15. MDM

    5 Pages

  16. MXM

    5 Pages

  17. SMX

    8 Pages

  18. RD-40

    2 Pages

  19. EWN-Y

    8 Pages

  20. EWN-A

    2 Pages

  21. MX

    8 Pages

  22. HRP

    2 Pages

  23. MDM NP

    8 Pages

  24. FW/-H

    12 Pages

  25. Serie YMD

    8 Pages

  26. Serie CFD

    12 Pages

  27. Serie FA

    12 Pages

  28. Air pumps

    8 Pages

  29. Serie MDT

    2 Pages

Archived catalogs

  1. RD

    4 Pages

  2. Hicera pumps

    4 Pages