FEATURES: Spring to lock when actuator is inserted. Energise solenoid to unlock. GUARD LOCKING SAFETY INTERLOCK SWITCHES Guard Locking Switch Metal Type: RAMZLOCK KLTM-RFID Solenoid Locking Door Interlock Safety Switch with Integral Unique RFID Coding featuring Guard Holding up to 2000N (200Kg) (F1Max) IDEM's KLTM-RFID Series Guard Locking switches are tongue type safety interlock switch incorporating traditional mechanical antitamper tongue technology (featuring IDEM's patened cam system) but also incorporating uniquely coded RFID non contact coded sensor technology in one device. They interlock and hold closed guard doors to protect operators from moving or hazardous machinery. They are suited to where a high anti-tamper technology is required to prevent accidental or deliberate attempts to by-pass the interlock. Both technologies must be satisfied to enable the machine to be started. They have a rugged metal body design and have been developed with a maximum holding force of 2000N to keep medium to large guard doors closed until hazards have been removed. IP67 enclosure protection is maintained by a double seal lid gasket design and metal fixings. They have a low profile and fixing holes are on an industry standard 73mm centre to enable easy retrofitting to new or existing guards (or where extra anti-tamper is required). CONTACTS: KLTM-RFID (incorporating RFID coding) 4NC Safety Contacts 1NO Auxiliary PNP Signal (Guard Open) 1NO Auxiliary PNP Signal (Guard Locked) LED1 RED Solenoid Power On LED2 GREEN Switch Locked LED2 YELLOW Diagnostic Fault FUNCTIONAL SPECIFICATIONS: Positive Break Contacts to EN60947-5-1 High Functional Safety to ISO13849-1 Rugged Die Cast Metal Housing with Stainless Steel 316 Head Will fit on 73mm fixing centres Connects to most Safety Relays to give up to PLe Cat.4 M23 Quick Connector version available for ease of installation 2 manual override points LED diagnostics for Solenoid, Lock and faults For all IDEM switches the normally closed (NC) circuits are closed when the guard is closed actuator inserted. Type: KLTM-RFID Mechanical and RFID Coding Standards: ISO14119 EN60947-5-1 EN60204-1 ISO13849-1 EN62061 UL508 Safety Classification and Reliability Data: Mechanical Reliability B10d 2.5 x 106 operations at 100mA load ISO13849-1 Up to PLe depending upon system architecture EN62061 Up to SIL3 depending upon system architecture Safety Data – Annual Usage 8 cycles per hour/24 hours per day/365 days PFHd 3.44 x 10-8 Proof Test Interval (Life) 35 years MTTFd 356 years KLTM-RFID Supply/Solenoid Voltage 24Vdc Solenoid Wattage 12W Thermal Current (lth) 5A Rated Insulation/Withstand Voltages 600Vac/2500Vac Travel for Positive Opening 10mm Maximum Approach/Withdrawal Speed 600mm/s Holding Force F1Max 2000N Fzh 1538N Body Material Die Cast Metal (painted red) Head Material Stainless Steel 316 Enclosure Protection IP67 Operating Temperature -25C +40C IEC 68-2-6 10-55Hz + 1Hz Vibration Excursion 0.35mm 1 octave/min Conduit Entry Various (See Sales Number) Fixing 2 x M5

Guard Locking Switch Metal Type: RAMZLOCK KLTM-RFID Fixing Holes - FRONT ENTRY SCHEMATIC CIRCUIT: KLT-RFID Version (incorporating RFID Coding) SALES NUMBER RAMZLOCK KLTM-RFID Switch Supplied complete with uniquely coded actuator SUPPLY VOLTAGE/HEAD POSITION M20 Actuator Entry Positions: Front Entry Actuator Entry Positions: Rear Entry Front Entry (Upper)

SECTION 5 GUARD LOCKING SAFETY INTERLOCK SWITCHES Guard Locking Switch Stainless Steel Type: KLT-SS-RFID FEATURES: Spring to lock when actuator is inserted. Energise solenoid to unlock. Solenoid Locking Door Interlock Safety Switch with Integral Unique RFID Coding featuring Guard Holding up to 2000N (200Kg) (F1Max) IDEM's KLT-SS-RFID Series Guard Locking switches are tongue type safety interlock switches incorporating traditional mechanical anti-tamper tongue technology (featuring IDEM's patented cam system) but also incorporating uniquely coded RFID non contact coded sensor technology in one...

Guard Locking Switch Stainless Steel Type: KLT-SS-RFID_ Fixing Holes FRONT ENTRY RFID ACTUATOR