BRUSHLESS DC MOTOR DRIVER - 5 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

Catalogue excerpts

BRUSHLESS DC MOTOR DRIVER Special for For small CNC Milling and Drilling Machine with Mach 3 Software Summarize ◆ AC220V power supply for ◆ Rated power 1500W ◆ rated speed to 6000RPM, speed range of 400-6000RPM, acceleration time 5S. ◆ PID closed-loop speed and current dual-loop regulator, speed-loop control accuracy of ± 1% ◆ has a limited flow, start-up failed, blocking switch, the module protection ◆ have the machine stop switch, protective masks, opening the door electronically controlled limit protection ◆ LCD display with the actual speed machine tool spindle and the work of the drive, and speed showed an accuracy of ± 2% ◆ regulating the use of key board drives the work of the state, operation is simple and convenient ◆ outside the user interface used to control the work of the drive, and easy to implement digital control of the working drive. Feature This series of Brushless DC Motor Drive Unit is designed as specific systems for some small milling machine. Motor driver can control the start, stop, acceleration, deceleration, forward , reverse, tapping, current limiting protection, stop, open doors electronically controlled power-off protection and turn off the protection of protective masks, it can be outside the user interface control. Overload protection: motor load of more than 1.5 times the rated load immediately 30S downtime, protect the code at the same time show that E5. Safe Notice Please read safety warning below carefully before Installing and operating this controller 1. This product should be installed and serviced by a qualified technician , electrician ,or electrical maintenance person familiar with its operation and the hazards involved 2. Insulated adjustment tools must be used when working under power .Do not touch the PCB board and junctions when working under power 3. All output and input terminals are NOT isolated from the incoming supply www.ICHmo.com Page

 Open the catalogue to page 1

Power board - Function of Terminal block loCH www.ICHmo.com Page 3 of 3 SDR-REV-1A

 Open the catalogue to page 2

Control Board - Function of Terminal block

 Open the catalogue to page 3

Keyboard Setting 1.System in accordance with the wiring diagram to connect after a good line, or if the SA at this time SQ1, SB1 are closed to disconnect SQ2. The buzzer sounded a "drop", LCD display "0000, FOR, STOP", key board "FORWARD, REVERST, TAPPING, START" keys are valid, machine tool spindle and the spindle motor speed ratio of 1:1, indicating Speed is a motor speed of 1:1. 2. Press "START" key to switch the drive motor is displayed is the lowest speed to 400RPM ± 10% runs, start-up time. For the most high-speed motor 6000RPM ± 1%. 3.Every move the "+" allows a driver to increase motor...

 Open the catalogue to page 4

LCD digital display through four of the actual motor speed (fixed speed than the spindle speed), "FOR" that is being transferred, "REV" said inversion, "STOP" to stop that. Instruction-driven work. Running Condition loCH www.ICHmo.com Page 6 of 6 SDR-REV-1A

 Open the catalogue to page 5

All I.CH MOTION CO.,LTD catalogues and technical brochures

  1. D202A1

    1 Pages

    En
  2. D252A4

    1 Pages

    En
  3. D362

    1 Pages

    En
  4. D372B3

    1 Pages

    En
  5. D482G2

    1 Pages

    En
  6. H571

    2 Pages

    En
  7. HP281

    1 Pages

    En
  8. H1101,1106

    1 Pages

    En
  9. HS561

    1 Pages

    En
  10. HS601

    1 Pages

    En
  11. HS861

    1 Pages

    En
  12. H364

    1 Pages

    En
  13. H391

    1 Pages

    En
  14. H392

    1 Pages

    En
  15. H421

    1 Pages

    En
  16. PM STEP MOTOR

    10 Pages

    En
  17. BLDC Servo Motor

    5 Pages

    En