• Products
  • Catalogues
  • Projects
  • News & Trends
  • Exhibitions

Multi Task System - 24 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

Catalogue excerpts

Multi-Task System MTS System I with Half-Length Options IAC Industries’ MTS upper structure for stand alone workbenches enables users to configure above-theworksurface storage and accessories into an organized, task-oriented working environment that will adjust up and down with the worksurface to which it is attached. MTS Systems are excellent for upgrading your existing benches on a budget. • 3-post vertical mounting structure for lights, shelves and many other productivity accessories. • Worksurface-mounted MTS mounts to 1.25˝ and 1.75˝ worksurfaces with 1.5˝ rear overhang. • Frame-mounted MTS mounts to any thickness of worksurface with 2.5˝ rear overhang on 30˝ deep benches and 4.5˝ rear overhang on 36˝ deep benches. ordering tips from IAC... Select “Customer Installed” when retrofitting to existing workbenches. MTS and options shown here with Pro Series 950 workstation Worksurface Mounted Tie Beam MTS Systems Features… MTS Vertical Double Slots Mounting Brackets Frame Mounted • Heavy gauge verticals and tie beam at top of frame system • Three* posts provide two side-by-side accessory mounting areas • Half-length options are easy and convenient to adjust shift to shift if needed • Options can be aligned or independently adjusted for maximum flexibility • Slots are on 1˝ increments center to center • Retrofits to most other workbenches • If worksurface is adjustable, options move accordingly • Smaller size frames easily mount to larger benches • Unlimited flexibility in arranging workstations to fit changing requirements *48 inch units have two verticals.

 Open the catalogue to page 1

System I Frame Components Multi-Task System Frame Mounted System The frame mounted MTS System uses a Pan Structure that mounts underneath the worksurface at the rear with gussets. The verticals bolt to the pan structure and are behind the worksurface, therefore not using worksurface space. Bench Length Part Number *Two outside verticals only; no middle post. Frame Mounted MTS Systems cannot be retrofitted to existing benches Frame mounted detail MTS and options shown here with Pro Series 950 workbench Worksurface Mounted System The worksurface mounted MTS System is mounted to the worksurface using...

 Open the catalogue to page 2

Multi-Task System System I Utility Shelf The MTS Utility Shelf provides off-the-worksurface storage in depths of 12˝ and 15˝. Standard shelves are metal; ESD shelves are metal with ESD laminate, snap and coiled ground cord. The shelf angle is adjustable from 0-15° and is formed from 16 gauge steel. The shelf lip acts as a parts cup rail, and the 12 gauge brackets angle and slide in, providing secure positioning. Due to bracket constraints, shelves cannot be mounted end to end to form one continuous shelf the entire bench length. Bench Length 48˝ Shelf Length Standard Shelf Approx. Load Capacity:...

 Open the catalogue to page 3

Multi-Task System System I Parts Cup Rail The single Bin Rail is available as either standard or ESD. The ESD version has ESD paint, snap, and coiled ground cord. Both are easy to adjust. The 14 gauge formed steel rail attaches to accessory brackets and adjusts up/down providing a convenient storage area for parts cup bins. Bench Length Rail Length Standard Parts Cup Rail Black ESD Parts Cup Rail Spans half length of MTS except on 48˝ systems. System I Multi Bin Rail Comes either standard or ESD, the 6˝ high, 18 gauge uni-web panel is mounted to 14 gauge brackets. There are six rails per section,...

 Open the catalogue to page 4

Multi-Task System System I Accessories – Cont. System I Electrical Outlet Channel The MTS Electrical Channel is mounted to 14 gauge brackets and can be positioned where electrical access is needed: at the work surface; above or below shelves for test equipment, etc.; or anywhere along the verticals. The electrical channel comes with an On/Off rocker switch, 15 amp circuit breaker, 8 ft. molded power cord, and six or eight outlets. Bench Length Part Number Channel Length System I Flipper Door Cabinets Flipper Door Cabinets provide horizontal, lockable storage for books, binders, instruments, and...

 Open the catalogue to page 5

Multi-Task System System I Isolation Screens Available in two heights, 24˝ and 36˝. When used side by side, they act as a privacy panel providing an area to display drawings or other information. With two 14 gauge brackets per side to provide support, the isolation panel mounts behind the verticals so it doesn’t intrude upon worksurface, thus freeing up area in front to mount other options if needed. Fabric Covered Isolation Screens Each Isolation Screen fills half the width of the MTS Structure Use pushpins to secure documents and drawings. Fabric provides added sound absorption. Metal Isolation...

 Open the catalogue to page 6

Multi-Task System System II with Full-Length Options System II Upper Structures IAC Industries’ MTS System II upper structure for stand alone workbenches utilizes a two-verticalpost design. The absence of a middle vertical, as used on the MTS System I, allows the mounting of full length accessories such as shelves, parts cup rails, and electrical channels. The MTS System II is also available for Instrument Shelves. • Two-post vertical mounting structure for lights, shelves and many other productivity accessories. • Mounts on IAC Isles Series Workbenches and Pro Series Workstations. • Worksurface-mounted...

 Open the catalogue to page 7

Multi-Task System System II Utility Shelf The System II Utility Shelf provides off-the-worksurface storage in depths of 12˝ and 15˝. Standard shelves are metal; ESD shelves are metal with ESD laminate, snap and coiled ground cord. The shelf angle is adjustable from 0-15° and is formed from 16 gauge steel. The shelf lip acts as a parts cup rail, and the 12 gauge brackets angle and slide in, providing secure positioning. Bench Length Shelf Length Standard Shelf Approx. Load Capacity: 50 lbs. May also be used on a System I Frame, as a full length option Quick Release Handle System II Pan Shelf The...

 Open the catalogue to page 8

Multi-Task System System II Accessories – Cont. System II Parts Cup Rail The single Bin Rail comes with either standard or ESD. The ESD version comes with ESD paint, snap, and coiled ground cord. Both are easy to adjust. The 14 gauge formed steel rail attaches to 14 gauge accessory brackets and adjusts up/down providing a convenient storage area for parts cups. Bench Length Rail Length Standard Parts Cup Rail Black ESD Parts Cup Rail May also be used on a System I Frame, as a full length option System II Multi Bin Rail Comes either standard or ESD, the 6˝ high, 18 gauge uni-web panel is mounted...

 Open the catalogue to page 9

All IAC INDUSTRIES catalogues and technical brochures

  1. MTS Rolling Carts

    16 Pages

    En