pop-up belt sorter - HYTROL - #2

Standard Specifications - Conveyor ProSort SRT

BELT- Ultimate 240 Black SC 7/8 in. wide with alligator 125 staple lacing.

BED- UHMW wear strip spaced every 2-1/2 in., Mounted in 6 in. x 1 In. x .12 ga. powder painted formed steel channel frame bolted together with splice plates.

END DRIVE PULLEY- 8 in. dia. with 1-3/16 in. dia shaft at bearings, fully lagged.

SNUB PULLEY - 4" dia. pulley with 1" shaft at bearings.

INFEED IDLER PULLEY- 3-1/2 in. dia. x 1-1/2 in. wide crowned sheave with precision bearings.

PNEUMATIC TAKE-UP - Take-up provides 14 in. of individual belt take-up. 25 PSI max on filter regulator. Need one pneumatic take-up per conveyor and one manual or pneumatic take-up for every 50 ft. of conveyor length.

AIR FILTER, REGULATOR - Supplied for main air line.

RETURN ROLLERS - 1.9" dia. galvanized tube with ABEC bearings. With

cardboard tube inserts.

BEARINGS- Sealed, pre-lubricated, self-aligning ball bearings with eccentric lock collars. Pre-lubricated ball bearings in return rollers.

SPEED REDUCTION- Sealed worm gear C-face speed reducer. #50 roller chain to drive pulley.

DRIVE - 1 HP- 230/460V -3 ph.- 60 hz. totally enclosed C-Face energy efficient motor with an AC variable frequency drive.

BELT SPEED- Determined by application requirements max 200 FPM.

TRACKING ENCODER - Provided on snub pulley in drive section. Contact factory for encoder specification.

CAPACITY- Maximum unit package weight 20 lbs. Maximum distributed load determined by number of belts. (See chart.) 100 ft. maximum length.

FLOOR SUPPORTS-Supplied as optional equipment.

• Standard Specifications - Small Roller Transfer

CAPACITY- Maximum unit package weight of 20lbs.

PACKAGE SIZE- minimum of 4 in. x 4i n. - maximum length of 24 in.

TRANSFER MECHANISM- Series of 7/8 in. dia. x 12 in. long drive rollers with 1/8 in. lagging. Driven by3/4 in. wide endless polyester belt.

AIR CYLINDER- 63 mm bore x 10 mm stroke guided cylinder.

AIR REQUIREMENTS- Working pressure 60 P.S.I. Free air consumption at 60 P.S.I., .024 cu. ft. per cycle.

AIR VALVE - 24-volt DC single solenoid 4 -way air valve MOTOR- 1/4 HP - 230 V (only) -3 PH- 60 HZ C-Face

AC DRIVE -1/2 HP - 460 V AC variable frequency drive, 460 V, programmed for 230 V output.

Close-up of Pop-Up Roller Transfer

Total Weight = Drive Weight + Roller Transfer Weight + (Conveyor Weight Per Foot x OAL)

• Optional Equipment

MANUAL TAKE-UP- See pneumatic take-up, less pneumatic cylinders.

FLOOR SUPPORTS- LS Type floor supports are available with a wide range of adjustment. Specify top of belt elevation. One support required at every bed joint and ends of conveyor. Holes are in feet for lagging to floor. Knee braces supplied with LS-7 supports and above.

GUARD RAILS- Continuous adjustable channel, fixed channel of type A & B angle. NOTE: If product comes in contact with guard rails, products may not divert.

POLY-TIER SUPPORTS - 36 in. to 120 in. support heights in 6 in. increments. Knee braces supplied.

SHAFT MOUNTED GEARMOTOR - Mounted at discharge end of unit.

MOTORS- Single phase, and other characteristics are available. For conveyor unit only.

ELECTRICAL CONTROLS- Push-button stations and AC variable frequency drive.

PROLOGIX CONTROL PACKAGE- Provides complete controls for proper sorter operation. Contact factory for details.

GAPPER SECTION- 60 in. long gapper unit used to pull gaps prior to diverting.

Hytrol Conveyor Catalog #589-Rev. 4 Effective December 2008

126