catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
P. 49
P. 50
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Flow transmitter, Flow-meter, Ultrasonic flow-meter, Sanitary flow-meter, Digital flow-meter
Text version of the page
Configuration31
HP289
The following steps are displayed when BATCH is selected. 2 BATCH L Maximum Batch Size which can be entered.3.2 xxxxxx Set to 0 if no limit on batch size.3 AUTO S Automaticrestart feature. Off Disable On Enable xx:xx If enabled, automatically restarts the batchxx:xx (mins:sec) after the end of the last batch.3.2.44 START T Slow start time. xx:xx Time, in minutes:seconds, when Relay 2will energize once the batch has started.3.25 COUNT PREST Prestop Quantity. TheBatch Total counts Up or Down. xxxx Quantity at which Relay 2 will de-energizebefore the end of the batch. (e.g., If the batch quantity is 100 liters and Prest is 2 liters, relay 2 will de-energize after 98 liters.)3.26 dn Count down from the batch quantity.3.2 up Count up from zero.7 T OUT TheSignal Timeout in seconds (Setting to 00 disables this feature.).3.2.28 AOC AutomaticOverrun Compensation. Note that the Signal Timeout must begreater than 0 (i.e., enabled) for this feature to work.3.2.5 En Enable. Dis Disable.
Model 214D-1 Batch Controller - 9075 5.2Entering the Batch Parameters
StepDisplayDescriptionTextRef 1 BATCH Set Batch Parameters OPTION Options (if installed)5.3 TEST Check Input Signals5.4 END Exit to normal operation CAL Setup Program Parameters5.1The following steps are displayed when BATCH is selected. 2 BATCH L Maximum Batch Size which can be entered.3.2 xxxxxx Set to 0 if no limit on batch size.3 AUTO S Automaticrestart feature. Off Disable On Enable xx:xx If enabled, automatically restarts the batchxx:xx (mins:sec) after the end of the last batch.3.2.44 START T Slow start time. xx:xx Time, in minutes:seconds, when Relay 2will energize once the batch has started.3.25 COUNT PREST Prestop Quantity. TheBatch Total counts Up or Down. xxxx Quantity at which Relay 2 will de-energizebefore the end of the batch. (e.g., If the batch quantity is 100 liters and Prest is 2 liters, relay 2 will de-energize after 98 liters.)3.26 dn Count down from the batch quantity.3.2 up Count up from zero.7 T OUT TheSignal Timeout in seconds (Setting to 00 disables this feature.).3.2.28 AOC AutomaticOverrun Compensation. Note that the Signal Timeout must begreater than 0 (i.e., enabled) for this feature to work.3.2.5 En Enable. Dis Disable.