Catalogs >
MOLDINO Tool Engineering Europe GmbH >
Epoch High Hard Radius EHHRE-TH3

Epoch High Hard Radius EHHRE-TH3
8Pages

Catalog excerpts

High Feed Radius End Mill for Hardened Steel Epoch High Hard Radius

Adopt the design of indexable high-feed cutter to solid end mill. High feed cutting for high hardness steel possible Lineup of Φ 1 ~ Φ 12 The multi flute end mill enables high efficiency machining even in small precision molds Approximate radius makes much thinner chip than real radius Vibration-free peripheral clearance geometry Newly developed coating "TH3" for hardened steel machining Carbon steel Alloy steel Stainless steel Pre-hardened Tool steel steel Mold making Mold making Parts processing Parts processing New Cutting Edge Geometry - Approximate radius makes much thinner chip than...

Open the catalog to page 2

Peripheral clearance geometry to reduce vibration Vibration-free peripheral clearance geometry Area without cutting edge Primary cutting edge Effect to suppress vibration at corner milling Work material：DACⒽ 49HRC　 Machine：Vertical MC (HSK-A63) 　 Tool：EHHRE6100-TH3 Cutting conditions：n=6,000min-1(vc =188m/min) v f =1,800mm/min (f z =0.05mm/t) Cutting amount ：0.3mm, Dry with air blow It is possible to minimize chatter vibrations at high speed machining and at corners, that can suppress unexpected chipping due to chatter vibration and efficiency reduction at corners. 90 degree corner milling...

Open the catalog to page 3

Work material Work material Work material Work material [Note] ® Use the appropriate coolant for the work material and machining shape. © Use a highly rigid and accurate machine as possible. © These Recommended Cutting Conditions indicate only the rule of a thumb for the cutting conditions. In actual machining, the condition should be adjusted according to the machining shape, purpose and the machine type. @ If the rpm available is lower than that recommended please reduce the feed rate to the same ratio. © Please use for contouring process. © Setting pick feed (ae) larger than lowest point...

Open the catalog to page 5

Field data Tool life evaluation of cutting SKD11H Tool size： φ10×6 flutes 　Work material：SKD11Ⓗ （60HRC）　Machine：Vertical MC (HSK-F63) Cutting conditions：n=1,900min-1 (vc=60m/min) v f =2,850mm/min (f z =0.25mm/t) ap 0.2mm ae 5.5mm 　　　　　　　　　OH＝30mm　Coolant：Air-blow Maximum flank wear width (mm) EHHRE-TH3 Conventional 1 (Conventional 4 flutes radius end mill) Chipping occurred at the beginning of cutting Conventional 2 Chipping occurred Micro wear EHHRE-TH3 achieves more than twice the tool life of conventional products High feed cutting of high hardness steel which was difficult with...

Open the catalog to page 6

Example of high-efficiency roughing of matrix high-speed steel Work size：100×100mm 　Work material：YXR33 58HRC）（　Machine：Vertical MC(BT40) Coolant：Air-blow R Cutting speed [m/min] Feed rate Chip removal volume [cm3/min] Machining time ■ Wear condition after cutting Work shape 100×45×Depth10mm ： Conventional 4 flutes radius end mill Conventional 4 flutes radius end mill Micro wear, possible to use continuously Chipping occured on R edge EHHRE achieved 5 times cutting efficiency than conventional tool. Good wear condition that can use continuously. High-efficiency cutting example of powder...

Open the catalog to page 7

The diagrams and table data are examples of test results, and are not guaranteed values. "Epoch" , “ ” and “ ” are registered trademarks of Mitsubishi Hitachi Tool Engineering, Ltd. in Japan. Attentions on Safety 1. Cautions regarding handling (1) When removing the tool from its case (packaging), be careful that the tool does not pop out or is dropped. Be particularly careful regarding contact with the tool flutes. (2) When handling tools with sharp cutting flutes, be careful not to touch the cutting flutes directly with your bare hands. 2. Cautions regarding mounting (1) Before use, check...

Open the catalog to page 8