Catalogs >
MOLDINO Tool Engineering Europe GmbH >
Carbide Non Step Borer series

Carbide Non Step Borer series
28Pages

Add to favorites

Catalog excerpts

Carbide Non-step Borer

Open the catalog to page 1

Carbide Oil Hole Non-step Borer Carbide Non-step Borer Automotive parts Machine parts Machine parts

Open the catalog to page 2

Carbide Non-step Borer Series Machine parts Cylinder block Machine parts

Open the catalog to page 3

Drastically improved machining efficiency High accuracy shank capable of shrink fitting. Reduces machining costs and CO2 generation! NSB specially shaped grooves enable non-step smooth boring High-efficiency boring even for environment friendly MQL machining. Oxidation and abrasion resistant TH coating. High-accuracy cutting edge. Carbide Oil Hole Non Step Borer High quality cutting edge enables long life and stable boring. Other manufacturer's new product The weak cutting edge causes cracks on the coating and unstable boring.

Open the catalog to page 4

Carbide Non-step Borer Series New product News ©mEM TH coating improves stability during high-temperature boring. Oxidation-resistant TH coating enables high-efficiency boring that causes high temperature. Oxidizing temperature and coating hardness Fragile oxide develops Fine, solid oxide with tight adhesion prevents wear. Specially shaped grooves discharge chips effectively zlfiflUpT (Mb:?) ©la'fb Torque change on the main spindle •IR Tool :20WHNSB0600-TH ^M\fk\^ cutting conditions: vc= 1 OOm/min f=0.15mm/rev H= 120mm ►ZrvS'tttDS'M Water-soluble coolant, internal oil supply :F*3p|5Sn>S...

Open the catalog to page 5

Sheet of stocked Items. ★ : Stocked Items of New Products. i '■ Stocked Items. @ : Scheduled to be sold from stock at selected dealers from June, 2010.

Open the catalog to page 6

Carbide Non-step Borer Series New product News cnniaM

Open the catalog to page 7

Item Code Item Code

Open the catalog to page 8

Carbide Non-step Borer Series New product News cnniaM Item Code fl^WHN^RI flflfl-TH fl^WHN^RI fl^fl-TH uoww niNoD i \JH\J~ i n

Open the catalog to page 9

Item Code

Open the catalog to page 10

Carbide Non-step Borer Series New product News cnniaM iM^i^^■ "FlS^P.^ Tool diatorelance : Refer under table Completely coated Item Code mwHN^Ri mn.TH

Open the catalog to page 11

SWISS 1 1 y©ilSSSR*#BS<rcffWo Tool diatorelance : Refer tool dia. tolerance table on p.11 Item Code

Open the catalog to page 12

Carbide Non-step Borer Series New product News CHEEM ■SSS: 1 1 y©ilSSSR*#BS<rcffWo Tool dia torelance : Refer tool dia. tolerance table on p.11 Item Code

Open the catalog to page 13

■SSS: 1 1 y©ilSSSR*#BS<rcffWo Drill diatorelance : Refer tool dia. tolerance table on p.11 *:Stocked Items of New Products. #:Stocked Items. □ :Stocked by specified distributor. Contact with our sales department.

Open the catalog to page 14

Carbide Non-step Borer Series New product News CHEEM Item Code

Open the catalog to page 15

Item Code

Open the catalog to page 16

Carbide Non-step Borer Series New product News ^MEEHM Cutting Conditions Setting of Cutting Conditions ^The above cutting conditions are based on the use of a water-soluble coolant diluted to a maximum of 20 times. When coolant dilution exceeds 20 times, decrease the cutting speed to the lowest in the specified range. When the tool diameter is ^5.0 or less, the coolant pressure should be 2.0 MPa or higher, and when the diameter is over ^5.0, the pressure should be 1.5 MPa or higher. ^When performing MQL (mist) machining, depending on the amount or status of spray from the tool, it may be...

Open the catalog to page 17

Cutting Conditions Wril^l^il/Elk'^U"?! Setting of Cutting Conditions *;ae©«iJ;rSSy^fSffl^^nlS«iJiSglEH©TPSd;DfiiS©*ftZr C«ffl<rc ^The above cutting conditions are based on the use of a water-soluble coolant diluted to a maximum of 20 times. When coolant dilution exceeds 20 times, decrease the cutting speed to the lowest in the specified range. When the tool diameter is ^5.0 or less, the coolant pressure should be 2.0 MPa or higher, and when the diameter is over ^5.0, the pressure should be 1.5 MPa or higher. ^When performing MQL (mist) machining, depending on the amount or status of spray...

Open the catalog to page 18

Carbide Non-step Borer Series New product News cmniaM Cutting Conditions WMy^ft<£>il/&<-'3U~C Setting of Cutting Conditions Be sure to refer to the boring procedure (under) when selecting a tool. ^The above cutting conditions are based on the use of a water-soluble coolant diluted to a maximum of 20 times. When coolant dilution exceeds 20 times, decrease the cutting speed to the lowest in the specified range. When the tool diameter is ^5.0 or less, the coolant pressure should be 2.0 MPa or higher, and when the diameter is over ^5.0, the pressure should be 1.5 SSWhen performing MQL (mist)...

Open the catalog to page 19

Cutting Conditions Setting of Cutting Conditions ^ The above cutting conditions are based on the use of a water-soluble coolant. ^ When performing MQL (mist) machining, depending on the amount or status of spray from the tool, the piping route, etc.; it may be necessary to reduce the cutting speed in order to perform machining. ^ When changing the tool, use a collet free from flaws and stains, and attach the tool firmly so that its runout is 0.02mm or less. ^ The above conditions apply to a hole-depth of 4 times the diameter or less. ^ When cutting fluid is used, reduce the cutting speed to...

Open the catalog to page 20

Cdrbide Non-step Borer Series New product News CHEEM Solution treatment + Age-hardening treatment [tDil^rft] work :INC0NEL718 fflmtW£+&$}ffltm£) Tool :03WHNSB0600-TH Cutting conditions •jPIlMljJilcJf Depth of hole : 1 8mtTl %0~Z>W Coolant :7j<j§'|4tO'i!l;"S F*9p|5$n)S Water-soluble coolant, Internal oil supply Cutting area Other manufacturers' solid drills 2.7 times greater drilling efficiency Comparison of machining cost • Comparison of Environmental C: Unit price of tool (¥/pc.) L: Tool Life (hole/pc.) Tm#: Machining time (min/lot) Ct. Tool cost (¥/lot) Tt: Tool replacement time (min/pc.)...

Open the catalog to page 21

Long-life operation possible with high-efficiency machining that uses an internal oil supply TH coating ensures longevity even for high-speed machining that causes high temperatures [tDil^ft] •SIM work :SCM440(30HRC) Tool :05WHNSB0600-TH Cutting conditions iUXT^xE Depth of hole :30mm (itDTO Up-grade hole %0~Z>W Coolant :7j<;§'tttiDr!lM F*9PI5SP>S Water-soluble coolant, Internal oil supply Machine parts Cutting speed Carbide Oil Hole Non-step Borer Other manufacturer's product The tool lasts 200% longer than those of other manufacturers. In the case of high-efficiency machining, it lasts at...

Open the catalog to page 22