HANNA instruments Industrial Catalog - 124 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

  13. P. 40

  14. P. 50

  15. P. 60

  16. P. 70

  17. P. 80

  18. P. 90

  19. P. 100

Catalogue excerpts

With Great Products, Come Great Results"

 Open the catalogue to page 1

Hanna Instruments® Customer support It is our philosophy that the best way to support our customers is to be closer to them. Hanna Instruments has over 30 offices around the world to provide our customers with dedicated service that is “just around the corner”. Technical department Contents Panel Mount Controllers . . . . . . . . . .3-10 pH/ORP with Sensor Check™ . . . . . . .3 pM,mV,Conductivity TDS Intro . . . . . .6 pH . . . . . . . . . . . . . . . . . . . . . . . . .7 ORP . . . . . . . . . . . . . . . . . . . . . . .8-9 Conductivity and TDS . . . . . . . . . . .10 Wall Mount Controllers ....

 Open the catalogue to page 2

CONTROLLERS > PANEL MOUNT HI 504 pH/ORP Controller with Sensor Check™ Digital Transmitter Input Many industrial applications require distances from the regulation system to the probe greater than the 15 meters provided by industrial probes. For these situations, the use of a transmitter is necessary. All HI 504 models are supplied with a digital transmitter input. Compared to a traditional analog transmitter, which has a maximum transmission length of 300 meters, our new digital transmitter, HI 504910 permits the connection with the controller at distances up to 1.2 km. The data transmitted can...

 Open the catalogue to page 3

CONTROLLERS > PANEL MOUNT HI 504 pH/ORP Controller with Sensor Check™ Receive electrode status & diagnostic messages on the lcd display or via your mobile-phone!* Sensor CheckTM pH/ORP As part of the powerful self-diagnostic functions of this instrument series, the Sensor Check™ system provides continuous inspection of probe status. The test is not limited to a simple signal that indicates an error in progress, but it reports the nature of the breakdown with a specific error code. With the use of the HI 504900 GSM module, errors or alarms can be sent directly to the operator's mobile phone as...

 Open the catalogue to page 4

CONTROLLERS > PANEL MOUNT HI 504 pH/ORP Controller with Sensor Check™ SPECIFICATIONS Programmable Hold System The hold function allows the user to stop the regulating action of the controller for programmable time periods. It is possible to activate the hold periods in correspondence to programmed operations, such as plant maintenance, cleaning procedures and instrument calibration. Resolution 0.01 pH; 1 mV/0.1°C above -10°C; 1°C below -10°C Accuracy (@20°C/68°F) ±0.02 pH; ±2 mV; ±0.5°C (-9.9 to 130.0°C); ±1°C (-30 to -10°C) Input Impedance 1012 Ohm Digital Output Isolated output, contact closed...

 Open the catalogue to page 5

CONTROLLERS > PANEL MOUNT pH, mV, Conductivity and TDS Panel Mount Controllers The HANNA instruments® line of industrial microprocessor-based controllers offer a multitude of features such as single and dual setpoints, ON/OFF, proportional and PID control, relay outputs, user-selectable zoom, bidirectional isolated RS232, RS485 port, isolated recorder outputs in mAmps and Volts, and much more. Recalls calibration data to ensure accuracy and compliance with procedures The primary display shows measurements, visible from a distance Displays various parameters and returns to normal operation mode The...

 Open the catalogue to page 6

CONTROLLERS > PANEL MOUNT pH 500 pH Controller SPECIFICATIONS Range 0.00 to 14.00 pH; -9.9 to 120°C Resolution 0.01 pH; 0.1°C Accuracy (@20°C/68°F) ±0.02 pH; ±0.5°C Input Impedance 1012 Ohm pH Calibration automatic, 1, 2 or 3 point, at pH 4.01, 7.01, 10.01 Temperature Compensation automatic (with Pt100 probe) or manual from -9.9 to 120°C Outputs digital: RS232 bi-directional optoisolated; or analog, galvanically isolated: 0-1 mA, 0-20 mA and 4-20 mA, 0-5 VDC, 1-5 VDC and 0-10 VDC Setpoint Relay 1 or 2 contact outputs SPDT 5A-250 VAC, 5A-30 VDC (resistive load) Power Supply 115 VAC ±10% or 230...

 Open the catalogue to page 7

CONTROLLERS > PANEL MOUNT mV 602 ORP Controller with Matching Pin and PID Control SPECIFICATIONS Range -2000 to 2000 mV; -9.9 to 120°C Resolution 1 mV; 0.1°C Accuracy (@20°C/68°F) ±2 mV; ±0.5°C Input Impedance 1012 Ohm ORP Calibration automatic, at 0 and 350 or 1900 mV Outputs digital: RS485 bi-directional opto-isolated; or analog, galvanically isolated: 0-1 mA, 0-20 mA and 4-20 mA, 0-5 VDC, 1-5 VDC and 0-10 VDC Control through analog output (single setpoint) Fully programmable microprocessor memory RS485 interface Differential input for ground loop protection Automatic 2 point calibration Last...

 Open the catalogue to page 8

CONTROLLERS > PANEL MOUNT mV 600 ORP Controller with Matching Pin SPECIFICATIONS Range -2000 to 2000 mV; -9.9 to 120°C Resolution 1 mV; 0.1°C Accuracy (@20°C/68°F) ±2 mV; ±0.5°C Input Impedance 1012 Ohm ORP Calibration automatic, at 0 and 350 or 1900 mV Outputs digital: RS232 bi-directional optoisolated; or analog, galvanically isolated: 0-1 mA, 0-20 mA and 4-20 mA, 0-5 VDC, 1-5 VDC and 0-10 VDC Setpoint Relay contact output SPDT 5A-250 VAC, 5A-30 VDC (resistive load) Power Supply 115 VAC ±10% or 230 VAC ±10%; 50/60 Hz Environment 0 to 50°C (32 to 122°F); RH max 95% non-condensing Fully programmable...

 Open the catalogue to page 9

CONTROLLERS > PANEL MOUNT HI 700•HI 710 Conductivity and TDS Controllers SPECIFICATIONS Range EC: 0.0 to 199.9 µS/cm; 0 to 1999 µS/cm, 0.00 to 19.99 mS/cm; 0.0 to 199.9 mS/cm; TDS (HI 710 only): 0.0 to 100.0 ppm; 0 to 1000 ppm; 0.00 to 10.00 ppt; 0.0 to 100.0 ppt; Temperature: -10.0 to 100.0°C Resolution 0.1 µS; 1 µS; 0.01 mS; 0.1 mS; (HI 710 only) 0.1 ppm; 1 ppm; 0.01 ppt; 0.1 ppt; 0.1°C; Accuracy (@20°C/68°F) ±0.5% F.S. (EC/TDS); ±0.5°C (0 to 70°C); ±1°C (outside) EC Calibration automatic or manual at 1 point Temperature Compensation automatic (with Pt100 probe) or manual from -10 to 100°C with...

 Open the catalogue to page 10

CONTROLLERS > WALL MOUNT Wall Mounted Controllers Microprocessor pH and ORP Controllers This line of industrial microprocessor controllers offers a wide range of features and functions such as single and dual setpoints, ON/OFF, proportional and PID control, relay outputs, user-selectable zoom, bidirectional isolated RS485, isolated recorder outputs in mAmps and volts, differential input, control through analog output and Fail-Safe Features. Simple to Use The large, dual-level LCD shows both pH (mV) and temperature and guides operators through calibration and programming with step-by-step prompts....

 Open the catalogue to page 11

All Hanna Instruments catalogues and technical brochures

  1. Salt meter

    2 Pages

    En
  2. Lab Guide

    32 Pages

    En

Archived catalogues

  1. Mini Controllers

    6 Pages

    En