Castors & wheels
140Pages

POINT M PRODUCTION Rue Marcel Poulain 60400 CRISOLLES French production site Guitel the group Guitel point m France Benelux Southern Europe North Africa West Africa The Middle-East H* Asia North America South America Guitel Ltd Great Britain "M South Africa Australia \ Guitel GmbH ■ & Guitel Polska - J Germany Northern Europe Eastern Europe

choosing a wheel | or a castor WHEEL FIXED CASTOR Tyre Wheel rim Fixed assembly Fastening holes Flanges Ball bearing Hub Tread Plain bore Roller bearing Axle Thread guard SWIVEL CASTOR Stem fitting - 1 CASTOR WITH LOCKING MECHANISM Bolt hole fitting Plate fitting Ball track Head seal Fork Rear locking mechanism Determining the load per wheel or castor Nominal load capacity The nominal load capacity (in daN) of the wheel or castor corresponds to the maximum load it can take while at the same time meeting the standardised test criteria (standard NF EN No. 12527) defined at the top of each...

What are the characteristics of the load to be moved? L_ In addition to its volume and dimensions, the total weight of the load to be moved is a dcisive factor when making a choice. In the case of material handling equipment, the weight of the load to be transported must be added to the unloaded weight of the trolley. J - TOTAL LOAD = unloaded weight of the trolley + load to be transported. To achieve a uniform distribution between the wheels, the unit load is calculated as follows: UNIT LOAD = total load / total number of wheels or castors - 1 The standard NF EN No. 12527 defines the wheel...

What traverse speed? The load capacity decreases with the material's traverse speed. Up to 4 kmph, the maximum acceptable loads are specified in this catalogue, under the conditions defined by the standards NF EN 12527 to 12532. Օ Over and above 4 kmph, the standard recommends other test parameters. The choice of a wheel or castor then presupposes a specific study. Technical advice In this case, choose a wheel or castor suited to the use you will make of it bearing in mind this advice from our technical department. Study the hardness of the tread, the strength of the swivel system and the...

untitled table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:8.00pt "Arial", sans-serif; } .font1 { font:31.50pt "Arial", sans-serif; } .font2 { font:4.60pt "Trebuchet MS", sans-serif; } .font3 { font:7.00pt "Trebuchet MS", sans-serif; } .font4 { font:8.00pt "Trebuchet MS", sans-serif; } .font5 { font:9.00pt "Trebuchet MS", sans-serif; } .font6 { font:28.00pt "Trebuchet MS", sans-serif; } .font7 { font:29.00pt "Trebuchet MS", sans-serif; } .font8 { font:41.00pt "Trebuchet MS", sans-serif; } CHOOSING A WHEEL ++ RECOMMENDED + POSSIBLE - ADVISED AGAINST Conductive...

untitled table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:5.00pt "Arial", sans-serif; } .font1 { font:5.30pt "Arial", sans-serif; } .font2 { font:6.00pt "Arial", sans-serif; } .font3 { font:8.00pt "Arial", sans-serif; } .font4 { font:29.00pt "Arial", sans-serif; } CHOOSING A CASTOR ++ RECOMMENDED + POSSIBLE - ADVISED AGAINST Operating characteristics Tread Dipped polyurethane Polyamide Polypropylene or Polychoc Sandwich Polyamide tread Resilex ring Thermoset resin Grey cast iron Shore hardness ±5 95 (A) 83 (D) 83 (D) 69 (D) Wheel rim Cast iron Aluminium PA PA...

What type of fitting? Plate fitting Rectangular, square, triangular. For mounting on an even surface. Bolt hole or eye-mounted fitting For mounting by means of a bose bolt. Threaded stem fitting Plain stem with wooden socket fitting Expanding plug fitted on bose bolt Circlip stem The parking of a pice of equipment in wind-exposed places or places where people pass, moving the equipment over a sloping surface or the necessity to immobilise it for it to be used (scaffold-ing, waste disposal container, display units, roller cabinets) and to avoid impulsive use justify resorting to a wheel...

table.main {} tr.row {} td.cell {} div.block {} div.paragraph {} .font0 { font:10.00pt "Arial", sans-serif; } .font1 { font:12.00pt "Arial", sans-serif; } .font2 { font:14.00pt "Arial", sans-serif; } .font3 { font:17.00pt "Arial", sans-serif; } .font4 { font:30.00pt "Arial", sans-serif; } .font5 { font:43.00pt "Arial", sans-serif; } WHEELS I Rubber-tyred wheels 180 lo 400 mm 50 to 200 daN SUPERMAN 8 80 to 250 mm 80 to 250 doN MANUTAL black 9 100 to 250 mm 100 lo 250 daN NORMEUROP black 10 160 to 300 mm 175 to 250 daN MANUBASSE 11 160 to 200 mm 175 to 200 daN MA NU MAT 12 80 to 200 mm 80 to...

RSILEX® P green Wheel rim: black polyamide. Tyre: green super-elastic bonded rubber tyre. Hub: roller bearing. Applications Manoeuvrability of a hard tread with all the advantages of a rubber tyre. 5-year bonding guarantee (under normal conditions of use). Silent in use due to super-elastic rubber. 0 il jDl 5^ 0 ■ ® Code EAN 13 100 35 45 i=; 12 200 0,200 3 81841* 314723 08184 1 2 125 35 45 i=i 12 200 0,300 3 81851* 314723 081851 1 40 60 20 300 0,600 3 81861 314723 081861 0 160 42 60 = 20 400 1,300 3 81921 314723 081921 1 200 46 60 i=i 20 400 1,300 3 81781 314723 081781 1 *Delivered fitted...

ALU'LASTIC Applications Flexible materials handling for heavy loads on uneven surfaces. Low starting effort. Lightweight wheel, resistant to wear and to side impacts. wheel rim: lightweight alloy, reinforced safety design. tyre: solid, black elastic bonded rubber. Hub: symmetrical, with precision ball bearings.

althane Applications Materials handling of heavy loads onindustrial surfaces in good condition. Rsistance to knocks and other types of impact. High degree of resistance to abrasion, hydrocar-bons and metal shavings. Towable up to 6 kmph (under normal conditions of use). wheel rim: lightweight alloy, reinforced safety design. Tyre: cast bonded polyurethane. Hub: symmetrical, with 2RS-type sealed precision ball bearings. 50 60 i « Code Code EAN 13 47 x 14 20 0,850 793 1 25 2000 339680 520100 9 50 60 47 x 14 20 1,105 793 160 2000 3 82803 314723 082803 9 339680 520101 6 20^1 700 1,485 793 200...