USM Go - GE Inspection Technologies - #1

Text version of the page

Technical Specifications - USM Go © 2009 General Electric Company. All Rights Reserved. Specifications are subject to change without notice. GE is a registered trademark of General Electric Company. Other company or product names mentioned in this document may be trademarks or registered trademarks of their respective companies, which are not affiliated with GE. CRxFlex is a trademark of GE Sensing & Inspection Technologies GEIT-20056EN(08/09) www.gesensinginspection.com Gate Independent Gates 2 gates (A and B), Gate B supports triggering by gate A Rectification Positive (POS) Full wave (FW) Negative (NEG) RF Measurement Peak JFlank Memory Capacity 2 GB SD Card. Up to 16 GB memory cards can be used Report Jpeg and BMP reports LCD Display Active Area W: 108 mm (4.25”) x H: 64.8 mm (2.55”) Size 5.0” Pixel Resolution 800 (W) x 480 (H) dot Connectors Probe Connectors Two LEMO-00 UT Output Connector SAP output, Alarm USB Interface micro USB connector SD-Card Connector Full size SD card slot to accommodate standard SD cards Pulser - All pulser measurements taken according to EN12668 specifications Pulser Mode Simulated spike standard, Uni-polar square wave optional Pulser Voltage (SQ Mode) 120 V to 300 V with 10 V step in a tolerance of 10% Pulser Width (SQ Mode) 30 ns to 500 ns with 10 ns step in a tolerance of 10% Pulser Amplitude (Spike Mode) Low: 120 V, High: 300 V Damping 50 or 1000 Ohms PRF Automatically optimized between 15 Hz to 2000 Hz, 3 automatic adjustment modes: AutoLow, Auto Med, AutoHigh - Optional manual control of PRF from 15 to 2000 Hz. Receiver Range 14016 mm at steel longitudinal wave (557”) Digital Gain Dynamic range of 110 dB, with 0.2 dB step Analog Bandwidth 0,9 - 17,4 MHz Filters Broad Band Low Pass 5 MHz (also 4) 10 MHz 13 MHz Environmental Battery 5.5 hours On board charging Off board charging with optional adaptor Proportional battery gauge indicating remaining operation time Charger “Universal” AC (100-240 V, 50-60 Hz) Meets CCC, CE, UL, CSA and PSE requirements Size 175 mm x 111 mm x 50 mm Weight 845 g (1.87 lb) with the battery Languages Russian, Portuguese, Italian, Polish, Czech, English, German, French, Spanish, Chinese and Japanese Protection as per Mil-Std-810F Damp Heat & Humidity (Storage) 10 Cycles: 10 hrs at 60°C (140°F) down to 30°C (86°F), 10 hrs at 30°C (86°F) up to 60°C (140°F), transition within 2 hrs, 507.4 Temperature Shock (Storage) 3 Cycles: 4 hrs at –20°C (-4°F) up to 60°C (140°F), 4 hrs at 60°C (140°F), transitions within 5 minutes, 503.4 Procedure II Vibration 514.5-5 Procedure I, Annex C, Figure 6, General exposure: 1 hr each axis Shock 6 cycles each axis, 15 g, 11 ms half sine, 516.5 Procedure I Loose Cargo (In Shipping Container) 514.5 Procedure II Transit Drop (Packaged for Shipment) 516.5 Procedure IV, 26 drops Operating Temperature Range 0°C to 55°C (32 to 131°F) Storage Temperature Range -20°C to 60°C (-4 to 140 °F) with battery, 24 hrs Dust Proof/Dripping Water Proof As per IEC 529 specification for IP67 classification Compliance EMC/EMI EN 55011 EN61000-6-2:2001 Ultrasound EN 12668 ASTM E1324 E317 ANSI/NCSL Z 540-1-1994 MIl STD 45662A MIL STD 2154 Options USM Go AWS Option AWS sizing tool according to AWS D1.1 Structural welding code USM Go Dac Option Dac sizing tool 16 points Compliant with EN 1712- EN 1713 – EN 1714 ASME & ASME III JIS Z3060 compliant TCG: 110 dB dynamic TCG: 120 dB/ìs slope USM Go DGS Option DGS sizing tool compliant with EN 1712 USM Go Embedded Datalogger Option Custom linear and grid file creation USM Go Squarewave Pulser Option Allows pulser parameters fine tuning Voltage adjustment from 120 V to 300V per 10 V steps Pulse width adjustment from 30 ns to 500 ns per 10ns steps USM Go Manual PRF and Phantom Option Allows Manual PRF optimization between 15 Hz and 2000 Hz per step of 5 Hz. Phantom PRF will help to identify ghost echo due to multiple reflections in low materials